Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828)
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (Washington, 1828) · View the page
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
MACHINE FOR SAWING CURVED TIMBFR,
By David Baker of Essex County, Massachusetts—See plate XXXV.
Specification. On the drawing, A represents the water wheel with two cranks; B, the pitman rods; C, the traverse bar which extends athwart the mill, and traverses vertically in grooves cut in the posts, or in boxes which are fastened to the posts; D, the bow or frame, which contains the saw, and which traverses horizontally on the bar C, and vertically in the frame K; E the saw pivots consisting of five parts, that marked 1, being turned to fit a socket in the bow and having a screw cut on the end, and a square shoulder to receive the washer and nut; 2, the washer; 3, the nut; 4, the fiel indented at proper distances to receive the points of the screws; 5, the screws, being four in number, and in pairs opposite each other, to confine the fiel; F, the saw which is so confined by the fiel and screws, as that the teeth will be in the centre of motion of the pivots; G, the gauge screws which are set in the carriage, and consist of four parts, 1, the screw with a shoulder to receive 2, which is a collar with a pivot to receive 3, which is a clamp having a screw by which the gauge plate is confined after it is adjusted, and 4, is a flange to keep the collar against the shoulder; H, the gauge stud, which is firmly fastened to the frame; K, having a fork on the lower side to embrace the upper edge of the guage plate; I, is a pivot on the upper side to receive the letter L. I, the gauge plate which has its lower edge confined in the clamps at the screw heads; after having been curved as desired, by means of the screws G. J, the regulator bar, which extends athwart the frame K, on which is fastened the regulator N, and has a triangle cut out of it forthe saw to turn in, and friction rollers on its edge, which embrace the saw, but without touching it, when the saw moves regularly perpendicular. K, the traverse frame, which is of the same width of the bow or saw frame, and carries that with it, having clamps to embrace the bow in the usual way, and is kept in its place by a groove in, or ridge on, the cross beams below and above the frame K, being made to correspond with the cross beams, and mounted on friction rollers; L. the tiller which is placed on the stud H, as a centre, the C.Brown del.
Original from NEW YORK PUBLIC LIBRARY
ARTOR, LENGX AND TILDEN FOUNDATIONS
arms extending at equal distances, on one of which at the end is a fork which embraces the upper edge of the gauge plate, and on the other at the same distance from the centre is a screw to confine the end of the regulator rod; M, which connects the tiller with the regulator N, which is curved with a radius corresponding to the distance from the centre to the arms of the tiller, having a fork on the inside to embrace the back of the saw without touching it, except when operated upon by the tiller, and slides in boxes arranged on the corresponding radius on the bar; J, taking the centre of motion of the saw as its centre. O, is a slide gauge to be used optionally instead of the screw G, consisting of two parts, 1, the bar which enters the carriage and is confined by a key having a fiel intervening between them, 2, is the poppet and screw which confines the gauge plate; P is a platform confined by screws to the carriage, having grooves in it to admit of its being adjusted, and on which is a dog connected with the guide; R, by a rack and pinion, R1, is the dog with a pinion, at one end and screws at the other, which is forked, the screws passing through the prongs into the timber confining it to the dog, which serves as its pivot, 2, the rack, 3, the guide arm, which is forked at the lower end, embracing the guide plate 4, and the upper end playing into the lower side of the rack, moving on a pivot at the same distance from the upper end as that from the centre to the teeth of the pinion, that end being a segment of a circle with cogs corresponding with the pins; 4, the guide plate, which is confined after adjustment, by the studs 5, which consist of parts, the stud, screws and washer, and which play in grooves in the guide-bows, 6, these being graduated and firmly fastened to the frame which the carriage traverses on; 7, bars which sustain the arm 3. S, balance wrench to be applied to the timber to counterbalance any crook in it, so that it may swing freely on the dog 1, as its centre, having a key slide, with a binding screw, and a weight like a steel yard; Q, friction rollers. This, which I consider as my invention, consists in so arranging the saw, as that it will move about the work and saw a crooked and winding kerf, without altering the direction of the timber, or the carriage on which it is sawed, (which passes through the mill as in straight work) by means of the above described machinery, except when crooked logs are to be sawed into boards; and when the apparatus constituting the guide; R, may be dispensed with, and a gang of saws may be applied instead of the single one. This apparatus may be applied to the common saw mill, with a little alteration, and will be useful in forming timber for ship building, and in trimming the edges of plank, and without the trouble of preparing a mould, by attending to the following adjustments, viz: The platform should be placed so as to accommodate the stick;
gauge plate crooked by the screws G, to the curve desired, and the guide plate by the studs 7, and all firmly fastened, which may be done in less time probably than would be necessary to plane boards for a mould, and it is very possible that before an ordinary hand would have prepared his mould, the rough stick would have become a timber ready to go into its place in the ship. Likewise for many purposes, other than ship building, the above may be advantageously applied, including all manner of curved stuff, such as the shafts and other posts of carriages, wheel felloes, &c.
Date of the Patent, August 6, 1828.
About this record
- Listed in
- the Mirror of the Patent Office (1828), Burke's List of Patents (1847)
- This patent has no X number: it is not in the list of patents restored after the 1836 fire. It is known only from the printed lists named below. The reference number (U…) is the IP Mall’s own.
- Listed in the Journal of the Franklin Institute or the Mirror of the Patent Office at the time of issue.