Drawings and documents
National Archives restored drawings: drawing
Benjamin E. Freymuth's Patent Drawing for a Alarm Bell
National Archives, Restored Patent Drawings (Record Group 241) · Full-size scan at the National Archives · Catalog record
Show the text on the drawing Hide (83 words)
Words on the drawing as machine-read by the National Archives; not checked. Useful mainly for searching.
DB. / ТОБОВ / Benjamin Freymuth / Alarm Bell / Patented December 22°.1814 / crann ATION / 2244+ 44. / LIV ION. / in / B. / nces. / hold the watch. / VIVI / 'er roith a qudgeon and tape / itch / the doo which falls in the ratchet wheel E / Ratchet wheel / ned to a spring / to disergage the Lever D / Patent Office May 12" 1838 / Made under the direction of the Commissioner of patents / un conformity with act of 3 "March 183ye / of
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (590 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 1.
2244X
B. E. Freymuth
Time Alarm.
Patented Dec. 22, 1814.
Page 2.
The schedule referred to in the Letters Patent and making part of the same containing a description in the words of the said Benjamin C. Freymuth himself of his alarm to be fixed to a Block or Watch.
Let there be provided a block of wood or other substance provided of sufficient weight to give it stability, this block should be about eight inches long four wide and three thick, more or less. Let there be a small stud raised near one end, with a groove or mortise in it to receive the pendule of a watch so that it may stand securely on one edge, the outer case of the watch must be taken off, and the back of the watch be turned towards the middle of the block. Then take a small cylindrical piece of wood, cork or other substance of about half an inch in diameter and somewhat longer, into the centre of this let there be screwed, at one end a gudgeon, with a socket in the other end similar to the pipe of a watch key and exactly to fit the fuzee arbor of the watch as its key does. The cork cylinder, on the other end of the pipe or gudgeon, is to have a narrow piece of oiled or varnished ribbon or tape, fastened to it, this is to be marked with the hours, as the cylinder is turned by the fuzee arbor in the running down of the watch, as the tape is wound round the small cylinder. The other end of the tape is fastened to the low end of a lever of about nine inches long from the fulcrum leaving the upper end of the lever about an inch and a half long. This lever is supported by a roller turning on gudgeons in two upright posts, of a suitable length, fixed firmly in the platform or block below. Near the lower part of the post is another roller turning with its gudgeons on the posts on this roller is fixed a ratchet wheel and near one end a small pulley, round which passes a cord, fastened to the pulley by one end, and to the spring of a common house bell by the other end. The spring is drawn up by winding the cord round the pulley, and is kept in that position by a dog or latch which falls into the ratchet wheel. If the alarm is required bring after the
Page 3.
tapes, say, of six hours, let the figure 6 on the tape be brought opposite a small wire leader pointing to the top of the cylindrical round which the tape is wound. The remaining part of the tape between the roller and the end of the lever to which it is fastened, will be so slack that it will take six hours to wind it round the roller so as to tighten it, at which time the tape drawing the end of the lever, will by means of another, acted on by the first, disengage the latter from the ratchet wheel, let loose the bell spring, & by its vibration ring the bell and give the desired alarm.
Benj. C. Freymuth
Patented December 22, 1844,
Describing the "Fire Alarm."
DATAMP: illustration
Illustrations from DATAMP
DATAMP (Directory of American Tool and Machinery Patents), via the Internet Archive · Archived DATAMP page
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.