Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828)
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 434 · View the page
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
BOILING AND CONVERTING SALT WATER INTO SALT.
By Osborn Parsons, of Pittsburg, Pa.
See plate XXXVIII, fig. 5.
Specification.—This improvement consists in placing metal tubes across the furnace, two inches, more or less, below the bottom of the metal pans, (when they are used,) each end of the said tubes extending through the walls on each side of the furnace, and through the sides of the wooden cisterns, placed on each side of the furnace, and metal pans, two inches above the bottom of the wooden cisterns. The said metal tubes may be six inches in diameter, more or less, eight feet long, more or less, according to circumstances, and open at both extremities.
The cisterns may be four feet broad, more or less; and their length governed by the length of the furnace, leaving sufficient room for the supplying of fuel. The bottom of the cisterns must be ten inches, more or less, below the bottom of the pans; and the top of the cisterns, equal to the top of the curb on the metal pans. There may be a communication at three different places in the sides of the metal pans, by means of three two-inch metal tubes, on each side of the metal pans, forming a communication with the water in the pans and cistern, through the walls of the furnace, and sides of the cisterns and pans, for the purpose of forming an equal surface of water in each of the vessels.
This principle may be applied also to the boiling of salt with kettles, by placing metal tubes between each kettle, or pair of kettles, and through the furnace as above described. But as it will be inconvenient to make a communication through the sides of the kettle, the wooden cisterns may rise above the top of the kettle, and the water introduced into them from the cisterns by means of stop-cocks; or, there may be a communication through the sides of the kettles, the same as the pans.
When brine requires purifying, it may be settled or filtered through sand.
The improvement of metal tubes and wooden cisterns, applied to boiling salt, is a saving of fuel, labor, pans, and kettles, grates, and furnaces; which arrangement and application, I claim as my improvement, and which I put in operation.
Patent dated April 4th, 1820.
REFERENCES.—PLATE XXXVIII. fig. 5.
No. 1. Salt pan, 18 feet by 5, 10 inches deep, more or less.
No. 2. Wooden cisterns, 14 feet long, 5 feet wide, more or less, 16 inchseep, more or less; 3 metal tubes, 8 feet long, 6 inches diameter, more or less.
—4, tubes to form an equal surface, 5, grates; 6, walls of the furnace; 7, aperture to supply the fuel; 8, tubes to supply the pan; 9, trough to supply water from the well; 10, settling trough; 11, graining kettle; 12, bottom of the chimney; 13, box and kettle to drain the salt from the bitter water.
METHOD OF CONVERTING HANGING PAPER INTO CARPETS, SO AS TO FORM A SUBSTITUTE FOR OIL PRINTED FLOOR CLOTHS.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.