Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (1,138 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 1.
X0003744
Aug. 26, 1823
85
Waldron Beach
Letters Patent
The Schedule referred to in these Letters Patent and making part of the same containing a description in the words of the said Waldron Beach himself of his improvement on Bergon's Self Sharpening Plough.
Bergon's Self Sharpening Plough for which this is an improvement is described as follows: "That pair of Ploughs which is forming the cutting part is that which separates or cuts the earth as soon as before it arrives at the mould board, and is commonly called the share. In most Ploughs the share is one part, but in this it is divided and distinguished by point and share. The point extends about three inches ahead of the share and is so formed that it may be reversed or turned up and down the share and under part thereof being precisely the same and tapering to the front and similar to a wedge, it is jugged in to fit up to the mould board, and fastened thereto by a screw bolt with a nut below the share in the opposite side, allowing room sufficient for that purpose. The sides thereof are formed with grooves to admit the share, and the back end thereof jugged in to fit up to the land side to which it is also fastened by a screw bolt in a horizontal direction. The share is also formed in such a manner that it can be reversed or turned over for each side, the opposite side being precisely the same. The ends thereof are so formed as to let into the point which hath grooves as above stated for that purpose, and catching or hooking to the mould board at the back end, it is also jugged in to fit up to the mould board and fastened thereto by a screw bolt. The mould board is formed by applying a true curve to the upper edge thereof. The diameter of which curve is taken from a curve which a sod forms when broken or detached from the earth by a plough and the edge of that curve to touch every part of the Plough. The other way by applying a straight edge to it in such a manner as to correspond to the end of a sod cut off at a right angle to the land side, and that side remaining on a mould board."
The castings are connected to the beam by an iron bar fastened to the mould board by a screw bolt and extending from that to the bolt which connects the land side to the mould board, which has a projection back (on the inside of the land side) for that purpose, and from that to another bolt before mentioned which connects the land side to the point, and fastened at the top of the beam by a nut and screw. This bar is also braced by another bar of iron riveted to it below the beam and extending
Page 2.
from that to the bolt which connects the land side to the tail. It is also fastened to the beam by a bolt passing through the mould board in front of the above mentioned bar and between the land side and the projection of the mould board before mentioned secured with a head on the inside below and a screw cut to the top of it to admit a nut above and below the beam. The object of the improvement in this Plough is to sharpen itself. All Plough shares wear mostly from below which causes the edge to incline upwards and the Plough becomes dull. This by being reversed turns the edge which was worn up, down and restores it to its primitive situation, which may be repeated several times before it will be necessary to get it renewed, which can be done at a very trifling expense. The point being made of wrought iron can be laid with steel for about 37½ cents. The share being of cast iron will cost about 30 cents. Thus it may plainly be seen that an immense trouble and expense will be saved to the farmer, as they will seldom be under the necessity of going to the blacksmith.
The improvements consist of the following particulars: It is: The share is formed similar to the above description except that the edge or cutting part is straight and the tines which fit into the moline or groove in the point are placed transversely or obliquely so that the tines which comes in contact with the point will be at the top of the share. The notches on the sides of the point are placed in an oblique or transverse direction so as to fit the said tines and lay the share on a straight line with the point. The share or standard is made of cast iron and attached to the mould board with a sharp edged or cutlass on its front to serve as a substitute for a coulter. On a coulter of the following construction may be attached at any convenient place where the standard and point are connected. That part of the coulter above the point and front of the standard or coulter is of a triangular form and of thickness sufficient to give it the requisite strength. There is a piece or part of the said coulter extending downwards which forms a key and doortail which secures or locks the point to the standard. If the Plough is used without the coulter a key and doortail is substituted to secure the point to the standard as aforesaid. On a two edged coulter the lower end which will be so constructed as to take the place of the said key and doortail may extend up to the beam. The piece forming the land side has a rabbit on the inner part to fit to the hinder part of the point. There is a projection on the bottom of the front end of the land side to cover the end of that bolt which is used in the absence of the coulter and key. There are two ribs cast on the inner part of the land side in such manner that they form a rabbit for the lower end of the handle. There is likewise a pro-
Page 3.
jection on the lower part of the right side of the middle board which comes in contact with the hinder part of the share and forms a support for the same.
Witnesses
D. B. Lee
William O. Bliss
Maldon Beach
(1122 Words)
Patented Aug 26, 1823
87
807d.
1146
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 11 (1833), p. 385 · View the page
Mr. Beach is the patentee of a self-sharpening plough, his first patent being dated August 26th, 1823.
Remarks. His present patent is for making a share triangular, and affixing it in such a manner that it may have three cutting edges; he also claims the "securing the reversing point without a bolt. His description is extremely brief, referring entirely to the drawing, without which the particular forms indicated could not be easily explained.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.