Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 61 · View the page
Show the transcription Hide (889 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
IMPROVEMENT IN THE LOOM.
By Joseph Scholfield, of Stonnington, Connecticut.—See Plate VII.
Specification—My improvement consists in placing two pieces of timber on the top of a square frame, composed of four ground sills, four up-rights, and four top pieces; similar to the common loom frame; which is, therefore, unnecessary for me to describe, unless it be to say, they have projections on the right hand end of the loom, on which the axle of a tappet wheel, composed of segments of circles on the circumference, and a camb wheel on the side of the same, works. This tappet wheel’s circumference, as well as its thickness, is divided in such a manner, that no sooner one tappet is off the end of one of the harness levers or jacks, than another is on; so that one of the jacks is always in motion.
At the side of these tappets or projections, is a camb-wheel, which works a jack that is connected to a short lever, running to the middle of a swinging or vibrating beam, or roller, hung under the upper part of the frame, cross-wise. To this beam, or roller, is fastened two small arms, which extend downwards, and are attached to the lathe, and wheel, when the camb-wheel moves on the jack and causes the lathe to come to the operator.
To carry back the lathe, the jack is made to fly up into the Camb-wheel, in an abrupt projection, formed by the inclined planes on the wheel, and two springs, of any shape, with cords or straps, running over rollers placed in the descending pieces of the lathe; at the side of these springs, are wires, with screws on their front ends, and Straps running round the yarn beam on the back ends, to regulate the lathe and yarn beam. On the front side of the tappet wheel, there are placed two camb-wheels, formed of as many projections as there are harness, straps, or shafts. These projections are rounding for three fourths of their length: The other fourth is straight to their ends, where they have an inclination of an obtuse angle.
These Camb wheels work on rollers at the ends of the front jacks, similar to those on the harness jacks, which I term the shuttle-jacks.
By turning the tappet-wheel, on which these last mentioned camb-wheels are placed, therollerontheendofoneoftheshuttlejacksismetatabruptendofoneofthestrojectionswhichcauseslevertofall suddenlyattthat end,andrise attherother;onwhichtwire thatrunsfromth坦entoalamb,connectedbyacross-straprounda roller,theend ofanotherlamb,anditsseveralspartsliketothe onejustdescribed.Wherethe camb-wheelhasdepressedsuddenly,theinner endofoneofthejacksb,yetheaidofthepartswhihave just described,andwith theadditionofare Rollerandarm,orlevers,或treadles,connectedtothelower part ofthelatheande peckerbands,theshuttleismade tofly oneway,andbymovingthe camb-wheelanotherprojection,itthrows itbacktherow.Several kindsoftappetwheelscanbe appliedtothesamemachine,foryanykindofcloth.
On the back end of the tappet wheel axle, there is placed a oog wheel of about 24 inches diameter, which works into a small pinion wheel about 3 inches diameter; one end of which pinion’s axle is supported on the hind connecting cross-piece of the loom; the other end is supported in a moveable arm, whose fulcrum is about the centre of the loom-frame. On the right hand end of this moveable arm, a strap of metal is fastened, which is connected to a lever, running at a right angle from the arm to the front, and alongside the right hand post of the loom-frame. The fulcrum of this lever, is on the end of a plate, and runs down, from the inside of the hand piece, which goes to the back end of the loom. In the front end of this lever, is cut an oblong mortise, through which passes a spring similar in shape to a capital S.
This spring is fastened on the inside of the front post. Within about one-third of its length from the upper or hand part of it, is a nick made by an inclined plane; stopping at that point abruptly, on its front edge, the object of this spring, is to suffer the front end of the lever, through which it passes, to fly up, and of course depress the other end of it, and throw the pinion in and out of gear, in case of accident, &c. When the loom is again to be put in motion, it is only necessary to cause the lever to pass back to the nick, which will throw the pinion, on which a drum and strap connected with the power is placed, into gear.
Under the lambs, which keep the harness of the loom straight, I place springs, spiral, or any other proper kind. All the looms that I ever saw, have only the lamb’s weight for the harness. What I claim as my invention, is the tappet, and camb-wheels; the rollers on the jacks; the connecting levers, forming a right angle from the tappet wheel; the springs under the lambs; the regulating wires, running from the lathe, to the yarn beam; and most particularly, the springs behind the lathe to bring it up against the cloth: in a word, the different parts of this machine, taken as a whole; so as to produce a loom, similar to that which I have described.
JOSEPH SCHOLFIELD.
ALEX. M'INTIRE,
S. A. ELLIOT.
Witnesses.
Date of the patent, September 9th, 1825.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Mirror of the Patent Office (1828), Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The specification was printed in the Mirror of the Patent Office (1828).
- Burke's 1847 Patent Office list gives the same patent.