Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 155 · View the page
Show the transcription Hide (793 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
TWIN LEVER PRESS.
By Charles Williams, of Petersburgh, Va.—See Plate XII. fig. 3:
Specification.—Cotton is the most valuable export of this country, and it should be prepared in the best manner for shipping. It should never be put in round bales, it injures its appearance—the carriage is higher, and it must be compressed for shipping. It should be packed in damp weather, or as soon as Ginned; it loses in weight by remaining open; hence the importance of a press in the house. The bales should have from 5 to 7 ropes, and be $4\frac{1}{2}$ or 5 feet long; if 2 widths, of bagging, 21 inches square, and weigh 300lb. If $2\frac{1}{2}$ widths, 22 by 30 inches, and weigh 400lb. (Cotton can be pressed too hard); the latter size is preferred, because 3 bales of 400lb can be pressed sooner than 4 bales of 300lb. and freight and storage is less. Every person owning a Gin, should have a good press built in the Gin House, the most important points are, that it should be cheap, durable, not liable to get out of order, and worked with few hands expeditiously. Horizontal presses will not make handsome bales, the lower end is harder and larger than the upper; the cotton cannot be so well stowed in the box. Cast-iron cog-wheels cannot be depended upon in cold weather. Iron screws are costly; work slow, with manual power, and have great friction. Wood screws require much room; it is inconvenient putting in the cotton; are not durable; $\frac{3}{4}$ power lost in friction. Levers have the least friction of all powers; but a single lever being over the box, there is no facility for putting in the cotton; these observations are founded on experience.
Plate 12 fig. 3, represents a Press placed under the Gin; the driver is taken out through the floor and set aside; the cotton is then put in with great facility. Instead of one lever over the box, I have two, one on each side, framed together; strong iron hooks, fast to the levers, with eye-bolts, play through openings and take hold of iron bars in the driver; the two iron bars and palls are like the rag of a saw-mill; the rest and pall (shown large at $n$) set on the cross-piece, and both bars go through it; the handle is worked as in pumping; the pails feed themselves; what $n$ gains, $o$ holds; when the levers are down to D, the springs force the keys into scarfs in the driver, and confine it down, while the leivers are raised for a new hold: this operation is repeated 8 times to complete a bale, and can be done in 15 minutes. After the bale is roped, the wedges are driven back, which loosens a moving plank, I, and the bale is relieved and easily rolled out.
The power of this Press is so great, that I have put 460lb of cotton into 5 yards of bagging, with one man; and I have taken a bale of hay, packed with a screw-press, weighing 476lb. and pressed it one-third smaller; every part is doubly guarded from danger; the operator cannot be hurt should any part break; the irons are all wrought, and can be repaired by any smith—the hooks feed themselves, and cannot be forced out of place; the strength of the iron is increased, as the pressure requires; at the first hold, the iron is $\frac{3}{4}$ inch square; at the last hold, 2 by 1 inch on each side;—a short handle can be used first, to expedite the operation; it may appear complex in the drawing, but it is simple in its operation.
There can be more bales packed in it, than in any other, with equal force. By making the bed, levers, and handle, longer, there is more power, but slower work. White oak is the best timber, but yellow pine is very good for床, cheeks, levers and plank. The driver and levers can be raised, by pulley or winch, but are more easily managed, when balanced by weights—stone will do for weight, and can be carried outside the house.
The driver may be connected to the leivers, by chains, instead of hooks, but the latter is most convenient. The levers may be drawn down by windlass, &c. but there is no way so powerful, compact and durable, as the toothed bars; they are placed 3 inches apart. The hooks bear, the three last times, on an iron bar, on top of the driver. My patent embraces the use of the twin levers in any way.
CHARLES WILLIAMS.
Date of the patent, June 3d, 1826.
Published accounts: journal notice
Notice in the monthly list of patents
Franklin Journal and American Mechanics' Magazine, vol. 2 (1826), p. 254 · View the page
In the lever press for packing cotton, and other articles, June 3, Charles Williams, Virginia.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.