Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828)
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 313 · View the page
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
IMPROVED BEE HIVE.
By Cuthbert Wiggins, Fayette Co. Pennsylvania.
Specification.—This bee hive is calculated principally for three purposes, as follow, viz.
First.—To prevent the bees from being destroyed by a species of pernicious worms which are known in most parts of the United States.
Secondly.—To secure the bees from the inclementy of the weather, and to prevent them from flying out of the hive in clear sunny weather when the ground is covered with snow. As when once they fall on the snow (which they are almost sure to do, owing to the weakness of their wings and a langor induced by the cold air) they are unable to rise again, and must inevitably perish.
40
Third.—This invention or improvement is calculated for the important purpose of taking the whole or a part of the honey without destroying the bees.
Before describing that part of the invention which is calculated to prevent the worms from destroying the bees, it may be proper to shew in what manner these worms originate and obtain possession of the bee hives:
In the summer months, a species of butterfly, or miller, as they are commonly called, deposits its eggs under the lower edge of the hive (and between the hive and the bench on which it stands) and among the scattered wax which falls from the bees and is blown under the edge of the hive, while they are engaged in building the cells; these eggs in a short time produce those worms which are so fatal to the bees. The worms insinuate themselves into the hive and extend a web before them which secures them from the bees. This web they fasten to the lower part of the hive and thence extend it to the lower edge of the comb, and thus continue rolling themselves into a cluster and extend their pernicious operations from bottom to top until they have destroyed bees, honey andcomb altogether.
When first hatched these worms are quite small, but in a few days they increase in size to the length of an inch or an inch and a half, and about the thickness of a small goose quill. I have endeavoured to smoke them from the hive with brimstone, but to no effect, for it did not in the least disturb them. I have also taken them out of their web and thrown them naked into the hive among the bees, who immediately dragged them out. By this means I discovered that if they were not secured by the web they could not injure the bees.
In order to prevent the deposition of these eggs, as before described, from taking place I have fixed a tin band, about two inches wide, round the bottom of the hive, under which the scattering waxbeforementioned cannot collect,which effectually prevents the deposition of the eggs,and consequentlythe productionof the worms. There are also three strips of wood placed on the inside of the hive and on which the hive stands, around which and under the bottom of the hive,the bees have a free thoroughfare;by this means the beesare enabled to blow away with their wings the scattering waxwhich fallstothebottom;而they arebuilding theircells these stripsalso serve thebees as ladders to ascend to theirwork,as theyalwayscommenceat thetop.Thebandmay bemadeofsheetironoranysubstance sufficientlythinandimpervioustopreventacollectionofthebeforementioneddrossyandscatteringwax,and consequentlya deposit ofthe eggs. Theshutter,whichisaffixedto thedoor andsecuredbyapinnadeoffire,serves tosecurethebeesfromtheinclementoftheweatherinthewinter months, and also to prevent them from flying out in warm days when the ground is covered with snow, as there are more bees lost in this way than any other, unless it be by the worms beforementioned. Near the top of the hive is a joint, in which is placed a wire cutter and which is held together by four small screws, for the purpose of taking a part of the honey without destroying the bees; the cutter, need not be sunk in the wood, nor the hive fastened together by screws when it is actually prepared for holding bees. It is only necessary to keep it secure until it reaches the office. When the hive is prepared to hold bees, the cutter must be placed in the inner joint, which must be the thickness of the wire shorter than the outside joint, so that the cutter will remain sufficiently loose to be drawn from the outside with ease when necessary. This will cut the comb off square. The upper part of the hive, which contains the best part of the honey, may then be lifted off; the cutter again fixed and another top of the same size put on, or a cloth thrown over so as to keep the bees down while the former top is emptied and set on again, when the bees will immediately go to work and fill it up again, and which may again be taken off as often as may be thought proper. The small pins in the top may be taken out and smoke blown in, in order to drive the bees down, if necessary, before the cutter is drawn. The hive may be so constructed as to enable the bee holder to take more or less honey as he may think proper; the modes of taking the honey will also be optional with him, which is one important advantage, as owing to the difference of climate in the different sections of the United States, the same time of taking them would not be proper in all climates, as in some the honey will be in perfection sooner or later than in others.
Date of the patent, Feb. 27, 1827.
Published accounts: journal notice
Notice in the monthly list of patents
Franklin Journal and American Mechanics' Magazine, vol. 4 (1827), p. 142 · View the page
In the bee-hive; C. Wiggins, Pennsylvania, Feb. 27.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 63 · View the page
In the bee hive; Cuthbert Wiggins, Fayette County, Penn. Feb. 27.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.