Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 151 · View the page
Show the transcription Hide (1,006 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
PUMPING WATER OUT OF VESSELS.
By Thomas Brownell of New York.—See plate XIV. fig. 1.
Specification. — The pumps may be in the usual form, and number; or of any other number that may suit the size and convenience of the ship or vessel to which they are attached. In the space between the capstan and main mast, I fix four standards of timber, six feet high, two and a half inches square, more or less. Upon the top of these standards, which are securely fixed to the deck below, I fix firmly a circle of plank from six to eight feet diameter (as the size of the vessel may admit), two inches thick and eight inches wide; in the centre of this plank, all round the circle, I bore, at equal distances from each other, sixteen holes, one inch diameter, and lined with iron; these holes are so situated, that if a straight line be drawn between each of them an equal distance from their centres, these lines and the holes shall altogether correspond with the thirty-two points of the compass. On the two standards next the pumps, I place a cross-piece of plank, bolted to the said standards; and to this cross-piece are bolted two jaws of iron, in which the lever, to be described hereafter, play upon bolts. These levers are of iron, or wood, and of a length sufficient to extend from the centre of the bore of the pumps, to the centre of the circle above described.
There will be as many levers as pumps. The fore end of each lever is attached to the piston rod of the pump which it is to work. On the top of the wooden circle are two iron standards, having bearings for the crank shaft to work in; these standards are formed with a screw bolt and nut below, with shoulders, which bolt passes down through any of the holes, before described, in the circle, and are fixed by a nut underneath. In these standards works the crank shaft, which is a bar of iron, reaching across the circle before described, and projecting on each side twelve inches or thereabouts, formed into a square at the ends, to receive a single crank, or other power, by which the shaft is to be worked.
The centre part of the said shaft forms a crank three feet deep, which crank is connected with a pitman, that is attached by a swivel to a cross bar below, to which the hinder ends of the levers that work the pistons are also fixed. About the middle of each piston rod there is to be a swivel joint, that the bucket may always retain its vertical position while the machinery is working, without an irregular friction; thus rendering the working easier, and the wear and tear less. On the end of the crank shaft is fixed a wind-wheel, suitably rigged and geared, each arm being six feet long, from the centre, and kept sufficiently distant from the bulwarks to avoid encumbering the deck. By shifting the standards before mentioned on the wooden circle in which the crank shaft works, we can now present the wind-wheel to any point of the compass, and so keep the pumps working as long as the wind blows. The levers that work the piston rods will not change their position by the alteration of the crank shaft, by reason of the swivel which connects them with the pitman and crank. The above mentioned standards, circular plate, levers, and wind wheel, are all moveable so that they may be taken away when not used, and replaced when needed; but when standing, give no obstruction to the working of the ship, nor to the passage on deck. The subscriber, in the year 1826, being at sea in a leaky vessel, with a machine as above described, working only one pump, of four inch bore, and the wind blowing a "whole-sale breeze," was able to keep the piston working at the rate of 3,500 strokes per hour, and discharging 2,400 gallons of water in the hour.
A part of the above machinery may be thus varied: instead of the two iron standards on the top of the wooden circle, two slides of plank may be substituted, having in them proper bearings for the crank shaft; near each end of these slides must be a hole corresponding in size with the holes in the circle, through which these slides are bolted and secured by a nut on the under side; and may be removed, if wanted, to any part of the circle.
Another variation may be, in substituting for the cross-piece and levers, as before described, a roller working on an axis in the two standards under the circle, next the pumps. Through the centre of this roller, at right angles with it, a scale beam passes, attached at one end to the pitman of the crank, and at the other to the piston rod.
When the wind fails, the wind-wheel may be removed, and a single crank placed on either end of the crank shaft; to the handle of this single crank may be attached a moveable lever or bar, about three or four feet long, which being moved horizontally backwards and forwards by one man, will work the pumps with very little labor, and discharge six or eight times more water than in the usual manner of working the pumps.
What I claim as my invention, is the combined machinery, as before described, for pumping ships by the power of wind, or by manual power in case of the wind failing. In testimony whereof, I have hereunto subscribed my name, this twenty-second day of March, in the year of our Lord one thousand eight hundred and twenty-seven.
THOMAS BROWNELL.
M. M'INTIRE,
ROBERT LITTLE,
Date of the patent, March 23, 1827.
Published accounts: journal notice
Notice in the monthly list of patents
Franklin Journal and American Mechanics' Magazine, vol. 4 (1827), p. 213 · View the page
In the method of pumping water out of Ships by manual power; Thomas Brownell, N. York, March 23.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 64 · View the page
In pumping water out of ships by means of wind; Thomas Brownell, New York, March 23. : In the churn; Samuel L. Bagley, Hillsdale, N. Y. March 24.
About this record
- Patentee
- the Journal of the Franklin Institute, Journal
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The patentee's full name comes from the Franklin Institute's journal.
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.