Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 50 · View the page
Show the transcription Hide (735 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
MACHINE FOR CRIMPING OR BLOCKING BOOT LEATHER.
By Samuel Morehouse, of Easport, Maine.—See Plate iv, Fig. 1.
Specification.—Be it known that I, Samuel Morehouse, of the town of East Port, county of Washington, and State of Maine, have invented a new and useful improvement in the boot crimping or boot blocking machine, not known or used before this my discovery, specified and described in the words following, to wit:
1st. A bench or platform, of a sufficient size for the purpose intended, is to be constructed of any suitable kind of hard wood, that is not liable to spring or cast; in which are to be made six mortises, for the purpose hereinafter described.
2d. Three jaws or cheeks are next to be constructed, of like material, with two tenons to each, at the foot or lower end, to correspond and fit mortises in the platform or bench, above described, with square mortises near the lower end of the front tenon of each, and at a sufficient distance from the shoulders, to admit the platform or bench between the shoulders, and the wedges to be inserted in these tenons for the purpose of securing and binding the jaws firmly to the platform. The four outside mortises in the platform, are to be made considerably wider than the corresponding tenons of the jaws or cheeks, in order to allow sufficient room for them to be extended to a greater distance, or contracted to a less distance, from the centre, or stationary jaw, to admit leather of a different thickness between them.
3d. Two wedges are to be made to fit under extended shoulders or grooves, between the centre and two outside jaws, so as to act laterally or horizontally, on the two outside jaws, in order to spread them from the centre one, as occasion may require.
4th. Two eye-bolts are to be strongly secured on the top of the platform, immediately forward of the opening between the outer and centre jaws, to receive the hooks of the crimping levers, hereinafter described, and to act as fulcrums to the lever.
5th. Two crimping levers, say three quarters to one inch in thickness, and of a sufficient breadth and length for the purpose, are to be made of good strong wood, and of the usual form of such machines in front, with hooks strongly secured to them at the lower end, for the purpose of being inserted in the eye-bolts of the platform before described.
6th. Iron rods or followers, made to correspond and fit the front part of the crimping levers, are to be placed over the top of the leather, when placed upon the crimping lever, and are to be secured at both the ends.
7th. Two screws of a sufficient length to extend through the whole three jaws horizontally, and project to a considerable distance beyond the outer ones, are to be strongly secured, one above the other, to the centre or permanent jaw, (by their being left square in that part) with threads at each end, and nuts or thumb-latches, and washers to fit them on both sides of the outer jaws, for the purpose of binding these jaws sufficiently close upon the leather.
Method of using this Machine.
The leather is first to be well wet, it is then to be placed upon the crimping lever, and secured by the follower; the lever is then to be hooked on the eye-bolt, the toe of the boot with the lever is then to be entered between the jaws, which are to be screwed up, so that the leather may go down easily about one third of the way; then after slacking the lower screws, drive the wedges at the foot of the jaws, which will close their tops more firmly upon the leather; then force the lever quite down, and the boot will be completely crimped or blocked.
SAMUEL MOREHOUSE.
C. H. W. WHARTON,
URIAH BROWN.
Witnesses.
REFERENCES.—PLATE IV. FIG. I.
A Platform, or Bench.
B Outer Jaws which are moveable.
C Screws, Nuts, &c.
D Centre or permanent Jaw.
E Wedges to spread the Jaws.
F Crimp levers.
G Iron follower to hold the leather on.
H Hooks and Eyebolts.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 138 · View the page
In the boot crimping, or boot blocking machine; Samuel Morehouse, of Eastport, Maine, June 19.
About this record
- Patentee
- the Journal of the Franklin Institute, Journal
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The patentee's full name comes from the Franklin Institute's journal.
- The specification was printed in the Mirror of the Patent Office (1828).
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.