Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 142 · View the page
Show the transcription Hide (954 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
HARROW AND PLOUGH HOE.
Improvement by Isham Cheatham, of Providence Inn, Chesterfield County, Virginia.—See Plate XI, Fig. 1 to 6.
Specification — To the common form of the harrow or plough is attached three or more helves, of hard wood, about fifteen inches in length, three and an half in breadth at top, and two and an half at the bottom, and two inches thick. These helves are attached to three or more longitudinal beams, which form the top part of the harrow, by means of mortises in the beams and corresponding tenons on the top of the helves, and are secured by pins passing through the top of the tenons, above the beams.
The means of attaching the hoes to the helves consists of two principles. First principle; a plate of iron, about one fourth of an inch in thickness, and of the breadth of the helve at the bottom, passes over the end of the helVE, from one side to the other, leaving a square space between the foot of the helVE and the plate, of about five eighths of an inch in depth, which forms the eye, to receive the corresponding shank of the hoe, which is square; the plate rises on each side of the helve to the height of two inches in front, and three on the back part, and is secured to the helVE by rivets: The hoe is made with two shoulders, and a shank, about three inches long; this shank passes through the eye of the helVE, about half an inch, and is secured on the back thereof, by means of a key or bolt, which is attached to the back part of the helVE, by two eye bolts, and can be moved up or down, as occasion requires, for securing the hoe to, or detaching it from, the helve. Another plate of iron, about one eighth of an inch thick, and of the breadth of the thickness of the helve, passes from the front part of the helVE to the back, close to the wood, raising on each side, front and rear, to the same height as the plate which forms the eye, and is secured by rivets.
Second principle. A helVE, secured to the harrow, or plough beams in the manner before described, having a tenon at the foot or bottom, of an oval figure, about three an half inches long and two inches broad, is to be fitted into the eye of the hoe, herein-after described.
The eye piece of the hoe, is constructed separately from the blade, and consists of a piece of iron about two and an half inches horizontal, and two inches in perpendicular depth at the heel; through which, near to theheel, is formed an eye, to receive the shank or tenon of the helVE, of an oval figure, about three and an half inches long and two inches broad, this piece of iron continues of the above dimensions, for about four inches, from the heel, forward to a shoulder,formed on each side above and below; at this point it is reduced to the perpendicular thickness of three-fourths of an inch,and continues to decrease in thickness and breadth,for about two inches forward,where it is only half an inch thick,and about one and an half inches in horizontal breadth. This latter described part,may properly be termed the bed or sill, on which the hoe is to rest,and through which passes a square mortise to receive a screw bolt, for the purpose of securing the hoe to the床,bY means of a female nut screwed beneath the床 and screwed upon the end of the screw bolt,till it draws the hoe firmly into the bed. At the small end of the before described bed or sILL,the iron assumes another shape and direction;it is reduced,laterally,to the thickness of half an inch,and rises again in the front part of the床,bY about half an inch above the upper surface thereof(which is the thickness of the heel of the hoe) thence,running horizontally forward, flush with the upper surface of the hoe;it terminates in an edge formed by this upper horizontal,and a lower inclined plane;
This part may be termed the lock or catch.
The hoes may be of various dimensions and figures,as the trowel,the coulter and shovEL or broad hoe;and are to be constructed,for the first described principle of adjustment,to the harROW,or plough, as follows;the plate of the hoe is reduced at the back part,to a shank of a length and thickness to suit the eye formed in the helVE before described.
For the second principle of adjustment;the hoe,near the heel,hAS mortise about half an inch square,to receive the screw bolTbefore described;about one and an half inches forward of this mortise is another oblong hole to receive the lock or catch of the eye-piece. The fore part of this hole,is to be bevelled on both sides,to an edge in the centre,at such an angle,as to fit the under inclined plane of the lock or catch. These hoes, when they become dull, by use on one side, may be turned over, when by use they will become self sharpened, and cut as well as at first.
In testimony whereof, I have hereunto subscribed my name and affixed my seal, this 30th day of July, 1827.
ISHAM CHEATHAM.
URIAH BROWN,
C. W. WHARTON,
Date of patent, July 31, 1827.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 140 · View the page
In the harrow and plough hoe, or a new method of attaching hoes of different descriptions, to the helve of the harrow and plough, for cultivating corn, wheat, rye, oats, cotton, tobacco, &c.; Isham Cheatham, of Providence, Chesterfield County, Virginia, July 31.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The specification was printed in the Mirror of the Patent Office (1828).
- The Mirror of the Patent Office's supplementary list gives the same patent.
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.