Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, vol. 6 (1828), p. 258 · View the page
19. For an improvement in Raising water from wells, cisterns, and springs, for domestic purposes; Samuel Smith, Mendon, Monroe County, New York, August 20.
Remarks. This resembles a pump, with a solid piston. The chamber or reservoir, is to be fixed in any place where water is wanted; a pipe, with a valve at top, leads down into the well or spring. In the description, no proportions are mentioned; in the drawing, the chamber has ten times the diameter of the suction pipe, and, of course, the water must pass through this with 100 times the velocity with which the piston ascends. To draw off the water, a cock is inserted through the lower part of the chamber; as the water is discharged, the weight of the piston, and the pressure of the atmosphere, will cause the piston to descend, and occupy its place. The most curious part of the structure, is the mode of working the pump. The piston rod is a toothed rack, into which a pinion works. This pinion is on the same axis with a wheel of three times its diameter, and this wheel is turned by a crank on the axis of a second pinion, which is about the size of the first; the piston will, of course, rise very slowly; this is evidently intended to accomplish the labour of filling the large chamber, which is to act as a reservoir; but why a single small pinion and crank were not preferred, we do not perceive. The water is not to be raised by alternate strokes of the piston, but by a single lifting operation, which is to be repeated, when the cistern, or chamber, is exhausted.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, vol. 6 (1828), p. 343 · View the page
What we claim as new and not in common use, and as our own discovery, in the above improvement and manufactory for grinding, and for the use of which we ask an exclusive privilege, is, that part of this mill which secures the following bush, and tightens or loosens it at pleasure; the manner of surrounding the stone by the hoop; the driver and its fixtures to carry and give steadiness to, and to level the runner; the securing and confining the runner and driver together; the manner of fixing the upper platform which receives and holds the stationary stone; the screws to raise or let down the said upper platform, and with it the stationary stone, and confine it to its proper and exact position; the fixtures of the damsel in the runner; and the use of the funnel for the purpose above specified. All of which last named specifications we claim to be new, useful, and our own invention: all other parts mentioned in the foregoing specifications have long been in common use. JAMES SMITH. WILLIAM SAPP. Specification of a patent for a machine for planting of different seeds. Granted to AUSTIN H. ROBBINS, and LEVI ROBBINS, Junr. of Denmark, Lewis county, New-York, August 13th, 1828.
Remarks. THIS machine, for which we claim a patent, and which performs the operation of planting, is placed upon a frame and wheel, similar in construction to that of a wheel-barrow. The length of the barrow frame is five feet, including the handles, and sixteen inches in width; and the wheel twenty-one inches in diameter. The axle of the wheel is like that of a common wheel-barrow, save near the wheel, there is a whirl turned on the axle, of different diameters, for the purpose of regulating the movements of the machine; and around which, a cord or a strap passes. There are two cross pieces, connecting the handles or arms; the first is thirteen inches, the second twentynine, from the centre of the axletree. From the centre of the second ROBBINS' Machine for planting Seed. cross piece, to the centre of the under side of the first, a piece, or perch, of wood, in a square form, passes, giving an inclined pitch of about five inches forward, to the same. This perch is secured to the cross pieces, at each end, by a bolt, screw, and nut; from this perch, two standards or posts arise, seven inches in height; on the first, immediately under a cross piece, hereafter described, is placed a shieve or pulley block, of different diameters, against which the cord or strap passes, in order that it should not chafe against the wheel, and to give ease to the motions of the other parts of the machine, the standards are united at the top by a cross piece, under which cross piece are two short knobs pressing upon the parts or boxes underneath; under this cross piece, and resting upon a short post or standard, which beneath rests on the perch, and also on the perch itself, is placed the improvement or invention claimed. The first thing to be noticed is, a circular box of the capacity of a half-gallon, more or less, resting in part upon the short post or standard, on the perch before described, and on another circular box placed directly on the perch below. The first box is perforated at top for the admission of a funnel, through which the seed is deposited in this box; and there is a circular plate of tin near it, capable of being turned, to close the aperture, when the funnel is removed. This box can be made of wood, tin, or sheet iron, or parts of either. There is a communication between, this box, and the one directly beneath, by means of a square orifice, at the inclined end of the box, guarded by a lip made of tin, to prevent the too free admission of seed, from the upper to the lower box. The lower box is five or six inches in diameter, and two and three-quarters deep. In this box is a circular plate, of wood or iron, to fit exactly in the box. The thickness of the plate, together with the diameter of the holes, regulates the quantity or number of seeds to be planted at one time. This circular plate is perforated with holes equi-distant from each other, and equi-distant from the circumference. This circular plate revolves round a spindle of sufficient length, to reach through the perch, the two boxes above, and the shieve, and about a quarter of an inch above the shieve, where it enters the cross piece, leading from the two upright posts, before described. On this spindle, immediately above the upper surface of the bottom of the lower box, is a shoulder, whereon the circular plate before described rests, and performs its revolutions. This spindle can be made either of wood or iron, the diameter about a quarter of an inch, and to correspond with the hollow of the cylinder, through which it passes. The passage of this cylinder through the upper box, or the orifice, through which it passes, is sheathed with tin. There is in the bottom of the lower box, an orifice directly over a hollow shaft, attached to the perch; the shaft is twenty inches in length. This shaft, at the bottom, penetrates the earth, and is sheathed with iron or steel in an angular form, the apex of the angle being towards the wheel; it may penetrate the earth to any required depth, and is open at the back and bottom, about three-quarters of an inch wide, through this the seed passes, and is deposited in the earth. This shaft is supROBBINS' Machine for planting Seed. ported below by a brace, secured to the second cross piece by a bolt, screw, and nut, passing through the perch, cross piece, and brace. A cord or strap being placed on a whirl of different diameters, on the axletree, and passing from thence round the shieve or pulley block, laying flat upon the outer surface of the upper box, by pushing and moving the barrow forward, the revolution of the wheel and axle gives motion to the shieve or pulley block; and that, by being connected by means of a hollow perpendicular cylinder to the plate in the lower box, causes a circular horizontal motion to be given to the said plate, perforated as before described. These holes of consequence pass over the aperture of the lower box. The seed passes from the upper box, through the aperture, guided by the tin lip, before described, falls into the lower box upon the inclined side, and upon the circular revolving plate; and as often as the holes of the circular plate pass over the aperture of the lower box, the seed goes from thence into the hollow shaft, and is operated upon by a spring attached to the lower surface of the upper box, in order that no interruption may occur in the passage of the seed from the box, to the depository in the earth. What we claim as new, and as our own invention or discovery in the above described machine, and for the use of which we ask an exclusive privilege, is, the whole machine above described, excepting the invention of the wheel-barrow. But we also claim the application of the wheel-barrow as our invention, to the use of the said machine. In witness whereof, we have hereunto subscribed our names the 1st day of August, in the year 1828. AUSTIN H. ROBBINS. LEVI ROBBINS, Jr. Remarks by the Editor. -The foregoing machine has been for some time in operation, and has been found to answer the intended purpose in the most perfect manner. An intelligent gentleman who resides in the neighbourhood of the patentees, writes thus; "there can be no difficulty in the application of this machine to the planting any kind of seeds, and any number of them at a time, and at any required distance, as fast as a man can walk. When the rows are set four feet apart one way, and eighteen inches the other, there is no difficulty, nor is it a very hard day's work for a man to plant ten acres, after the ground is properly prepared to receive the seeds." To the cotton planter, this machine will, we are persuaded, be particularly beneficial, not only as regards the saving of time, but also in the perfect regularity with which the rows may be planted.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.