Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 336 · View the page
Show the transcription Hide (956 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
MACHINE FOR WASHING CLOTHES AND CHURNING BUTTER.
By John Grout, of Tompkins county, New-York.
Specification.—A box made tight, in shape resembling a pentagon, except that the bottom is the segment of a circle, struck on the semi-diameter of five feet. Said box is three feet six inches long on the bottom, one foot six inches wide, and thirteen inches deep, made water tight; the upper edge of the ends of the box, two feet and two inches apart. The two upper sides of the pentagon are formed by doors hereafter described. At two feet six inches from the bottom, and five inches from the upper angle of the pentagon, make a hole through each side of the box two inches in diameter, for the roller of the beater hereafter described to roll in; cut off the upper angle of the pentagon at the centre of the hole. Fit into the bottom of the box six or eight strips at equal distance apart, five inches wide, one inch thick, and about two thirds of the length of the box; the top edge of the strips corresponding with the bottom, that is struck from the same Google
THENEW YORK
TILDEM FOUNDATIONS
centre; the ends of the strips slanted off to a mitre, so that the top will be shorter than the bottom. These strips should have a notch cut in the bottom, so that the water can run under them, and pass out at a hole in the bottom of the box. The same number of strips eight or ten inches long, and one inch thick, placed on each end of the box in a line with the strips on the bottom, said strips to be two inches wide, three inches from the upper end when in, and brought to an edge at each end. To make a beater take a piece two inches square, two feet and seven inches long for a shaft or roller, leave eighteen inches in the centre square, round the balance to the ends. Then take two pieces two feet and two inches long and four inches square, frame in at one end a girt the same size, seventeen inches long, that is to say, so that the first mentioned pieces shall be nine inches apart. Into the edge of the girt mortise and tenon five or six pieces, five inches long, six inches wide at the outer end, and reduced to the same size as the girt at the other end; frame the other end of the two pieces fast to the roller first mentioned, frame on to each end of the roller a piece of timber three feet long, four inches square at one end and three at the other, eight inches from the small end. Also, a girt at the small end, when made, is put into the box and swings on the roller in the holes above mentioned. The bottom of the box is raised one foot from the surface on which it stands on rockers struck from the same centre as the box, and made fast to the box by three strips of boards tenoned into the rockers.
At the upper sides of the pentagon fasten on two pieces on to each side of the box four inches wide, raised three fourths of an inch above the sides of the box, forming a rabbit for the door to shut in. These pieces extend down to the bottom of the box; the lower end of these trimmed off with the side pieces of the box, and the upper end cut off as the angle of the box. A little below the bottom of the doors on each side, halve on to the strips last mentioned a strip two inches wide, running lengthwise the box and projecting out five or six inches at each end for handles, at the upper edge of each end of the box or lower edge of the doors, put a strip across two inches wide raising half an inch and forming a rabbit for the bottom of the door. The doors made of boards with battens so as to fit the openings left at the upper end of the box, at the upper edge, on each end of one of the doors, screw or pin on a piece so as to shut up the hole made by cutting off the upper angle of the box; this is done for the purpose of getting the beater in and out at pleasure. The doors when shut are made fast by buttons near the top edge. The clothes are put into each end of the machine, divided as nearly equal as may be, and at every stroke with the beATER they roll over against the end of the strips in the bottom of the box.
43
The machine is operated with a handle of convenient length, made fast to the centre of the upper girt of the beater, or at the lower end of the piece on the roller with a hook and eye, and pulled and pushed alternately until the clothes are washed: when used as a churn, the inside work may all be left out except a plain beater, that is to say, the lower end of the beATER may be made of a board or plank with a number of holes in it; and is operated in the same way as when washing. The size of the churn or washing machine may be varied according to circumstances.
[No drawing is necessary.]
Date of the Patent, Oct 10, 1828.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, vol. 6 (1828), p. 393 · View the page
2. A machine for Washing Clothes and Churning Butter; John Grout, Caroline, Tompkins county, New York, October 10, 1828.
Remarks. There is a strong similarity between this machine and several of its predecessors; we, therefore, pass it over without attempting a further description, than merely to say that there is a box, or trough, VOL. VI. No. 6. - DECEMBER, 1828. 50 fixed upon rockers, with a beater and strips within the box, and that a rocking motion is to be given to the whole, when the machine is used.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The Mirror of the Patent Office gives a different date; the date shown follows the standard lists.
- The specification was printed in the Mirror of the Patent Office (1828).
- Burke's 1847 Patent Office list gives the same patent.
- Burke's 1847 Patent Office list gives a slightly different date; the date shown follows the standard lists.