Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 289 · View the page
Show the transcription Hide (3,364 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
MACHINE FOR SPINNING AND ROPING COTTON,
By John W. Wheeler, of Galway, Saratoga county, New York.
See Plate XXV.
The machine containing said improvements, may be made to propel any convenient number of spindles, from six to eighteen, and even more, according to the propelling power, whether it be by hand, water or steam. The size of the machine selected for description herein, is one calculated for eight spindles, and to go by hand; it has a frame consisting of four posts, of any wood of ordinary strength, from two to three inches square, or larger or smaller at the judgment of the machanic, and the quality of the wood. The two front posts are five feet five inches in length, exclusive of the tenon at the top. The two back posts are five feet and one inch in length, exclusive of the tenon at the top. The distance between the two front posts is two feet; the distance between the two back posts the same. The distance between the front and back posts at the bottom is one foot eleven and three-quarter inches, and the distance between them at the top of the back posts, measuring from the tenon of the back posts, is nine and one half inches. The inclination of these two pairs of posts is alike towards each other, on the right and left side of the frame, the front posts are united to the back posts by two cross pieces, of the size of the posts, one on each side, framed into the front and opposite back posts, about four inches from the bottom, and fastened with bed screws; a cross piece, of the size of the posts, is then framed into the two cross pieces, uniting the front and back posts, about six inches from the inside of the front posts, and fastened with床 screw. The back posts are united by a piece of like size, framed into each, about ten inches from the bottom, and fastened in like manner. The front posts at the top are framed into a plate of like size with the posts, by a tenon on the tops of the posts and mortises in the plate correspondent.
The plate extending beyond the posts on each side from two to three inches, and fastened with床 screw. The top of each of the back posts is framed and fastened in the same manner into pieces of like size, called plates, which extend four inches back of, and are at right angles with, the back posts, and reach to, and are framed into, the front posts, with like fastenings into these plates, so uniting the front and back posts at top, and extending from one plate to the other, are inserted two pieces called rails, each an inch one way, and one and one half inch in size the other way, to be framed into the plates; by mortises through the plates or partly through, and with tenons on the centre of the ends of the rails an inch square, the first rail to be placed back of the post, so that there will be six inches and one half inch between it and the front post, measuring on the under side of the plate, and the other still farther back, so that there will be three inches and three quarters of an inch between the two rails, and both to be so placed that if the back posts were extended upwards, the widest side of the rails would be parallel up and down with them.
These rails support the spindles, and to which the spindles are adjusted in the following manner: the rails are divided into spaces of convenient distance to place the spindles, which spaces are generally from two inches and a quarter to three inches.—The spindles are placed on the under side of these rails, and are adjusted to them as follows: in the centre of each spindle space, on the under side of each rail, a mortise is dug for each spindle about three quarters of an inch in length, about two eighths of an inch in width, and about a quarter of an inch in depth; on the upper side of the rails, immediately over the centre of the mortises, a hole is bored with an iron bit as large as the size of the rail will admit and about one quarter of an inch in depth; through the centre of these holes a hole is bored in the same manner, about a size less than the first made hole, reaching quite through to the mortise. Then take a piece of soal or harness leather, of about the length of the whole hole through the rail, and nearly as thick as the width of the mortise, and as wide as the length of the mortise, then cut the piece so as to leave a stem or tongue of the width of the diameter of the smaller hole, bored as above described in the rails, of the same length as the distance from the upper surface of the mortise to the top of the rails, and leaving the other end in a shape almost square and of a size to fit the mortise through the part of the leather which is made to fit the mortise; make two holes of the diameter of about an eighth of an inch each, then split that end of the leather fitting the mortise in the centre nearly up to the lower end of the stem or tongue, then take a flat piece of horn, about an inch in length and three quarters of an inch in width, (i.e. the length of the mortise) bore through one end of the longest way of it, two holes to correspond with those made in the leather, then insert the horn in the split end of the leather in such manner that leaden rivets may be put through the leather and the horn, and in that way the horn may be fastened and secured firmly in the leather, then bore a hole of about the size of the spindles intended to be used in about the middle of the horn, and about one eighth of an inch below the bottom of the leather. This piece of leather and horn, made in the manner above described, is called a poppet head, or spindle collar, wherein the spindles run. The poppet head or spindle collar may be made of raw hide cut into the same shape and size. The poppet head, or spindle collar, is then inserted in and through the mortise in the under side of the rails, the stem or tongue reaching to the top, a piece of leather of any thickness thought proper and of the circumference of the larger hole bored as above described in the top of the rails, with a hole in its centre of sufficient size to allow the stem or tongue of the poppet head, or spindle collar, to pass through, is then placed in the said larger hole, the said stem or tongue passing through it, and in the stem or tongue and above the circular piece of leather, a small pin of wood or iron is inserted through a hole made there for the purpose of fastening the poppet head or spindle collar. The pin to be inserted at a point that will make the spindles range with each other on the same level. The circular piece of leather, above described, is intended to lessen the noise of the machine, and, by increasing or diminishing its thickness, to raise or lower the spindles, as may be necessary in adjusting them to a level; at the back end of the spindle, immediately in front of the back poppet head, is a shoulder on the spindle to prevent it from slipping backward, at any convenient distance on that part of the spindles which lies between the front and back poppet head collars, are fixed on the spindles, by the spindles going through them endwise, whirls to receive the bands; they are solid cylindrical pieces of any kind of hard wood, about an inch long and about an inch diameter, with a groove turned round them to admit and hold a round band; on the spindles are placed a thin circular piece of wood, usual on common household great wheels, to keep the back part of the broach or cup of yarn upright, and stand in front of the machine; then at the right hand, on the outside of the front and back posts, fix, by proper fastenings, an iron shaft or axle, extending from the back post to a few inches forward of the front post; at the forward end of this shaft is fixed a crank and handle to turn a wheel, through which the shaft or axle passes, which wheel is placed close to and in front of the back post, and is constructed with a nave, or hub, and spokes very like the common small wheels used for spinning flax, with a diameter of about fourteen inches, the shaft or axle to be so placed as to cause the rim of this wheel to run near to, in front of, with an inclination parallel to, the back post. The shaft or axle is placed parallel to the plates in which the rails are inserted, and about seventeen inches below them. The rim of the wheel is about one inch wide and is made of raw hide limed so as to take the hair off.
Construct a cylinder of the diameter of the wheel for which you intend to make the rawHide rim; in this cylinder cut or turn a groove about an inch wide, on the surface of the cylinder and about three quarters of an inch deep, then cut a strip of raw hide about an inch and a halfwide and of a length about equal to the circumference of the wheel, then fasten it securely at one end in the groove, then bend it closely round the cylinder in the groove until it meets the fastened end, and then fasten the other end, if properly bent it will form a groove in the outer side of the raw hide. Let it remain until it is thoroughly dry, then turn or cut grooves in the outer ends of the spokes of the wheel proper to receive the bent and grooved rawhide, then take the raw hide fixed as above, and fasten it around the ends of the spokes fitted for it by nailing it to the ends of the spokes with cloutnails, and nail or cement the ends together. Then paste a strip of woollen cloth of the width of the raw hide rim with a glue paste, trim the edges of therim, and it is complete for receiving a round band.
About three feet two and a half inches below the under side of the back rail, a cross bar is framed by tenon and mortise and fastened with bed screws, fromand in onebackpost to andin the other, directly atthe back postitisof the same size as the post, gradually increasing in widthfrom eachpostto the middle of thebar,when it gets to be about four inches inwidthat themiddleofthecrossbar,on theuppersideapieceofwoodaboutelevenincheslong,treincileswide,andone inchand aquarterthick,isfastenedtothem cross bar,(crossingit atright angles)byawooden screw passing throughthe cross-bar and secured byawooden nut;near eachofthe ends of thepieceofwoodlastdescribed,astandard is erectedabouteleveninches inheight,atrightangleswiththesaid pieceof wood,byinsertinga roundtenonthrougharoundmortiseandpinningitontheunderside,thedistancebetweenthetwostandardsnearthetopwhere thegudgeonsholdingawheelare inserted,isfive andthreequarterinches;in these standards,andheld by them,isa wheel similar to the former,exceptingthedaveorhub,ofabouteighteen inches diameter,withthesamekind ofrim;the hub is five inchesand threequarters inlengthbetweenthestandards,theendofthehubtowardsthefrontpostsis about sixinchesindiameter,andcontinuesback towards the spokes of the samediameter the distanceofabout one inch and a half, and within the distance of theone inch anda半half,a groove,aboutthreequarters ofan inch inwidthatthesurfaceandabout threequartersof an inchdeep for thepurpose ofholdingaroundband,iscutorturnedinthehub.Thespokesofthewheelare setin the hub abouttwo inchesanda halfbackfromthesaidgrooves,andsoas tobeina rangewiththemiddleofthe two backposts;thediameterofthehub,attheplacewhere the spokes are inserted,isaboutthreeinches. Thegudgeons of the wheel run in ahorn,orlead,或lignumvitae box;insertedin eachstandard, aboutan inchfrom topofthestandards tothebackposts,aboutfourteen inchesbelowtheundersideoftheplates,connectingthe back poststo thefrontpostsarefastenedtworovesone ontheout,andotheronthereside ofthesaidbackposts;the rovess are about twofeet fiveinches long, three quarters of an inch thick, and one inch and a quarter wide. The wide side of each of them to be parallel with the back posts. The width between the roves to be equal to the thickness of the back posts which they embrace, and are fastened to each other at this distance apart by two pins, about three quarters of an inch in diameter, with shoulders and tenons mortised into the roves: the pins to be inserted at a distance about six inches from each end of the rails, about one half inch from the inside of each back post, and about three inches from each end of the roves; a wooden screw is inserted with the head or handle thereof on the outside of the outer rove and screwed into a nut cut for that purpose in the other rove; the object of these screws is to tighten or loosen the roves embracing the back posts; so that the rooves containing the friction pulleys, hereinafter described, may be placed higher or lower than fourteen inches as aforesaid, according to the judgment of the mechanic, or spinner, and as shall be required to make the length of that part of the band, measured from the top of one whirl of a spindle down round the friction pulley immediately between and below two spindles up to the top of the whirl of the other spindle, about equal to the length of that part of the band which touches the surface of the rim of the spindle wheel, about which equality is necessary to diminish the friction to the lowest degree. This principle is applicable to the geering of other machinery. Stand on the front side of the machine, then at a distance of seven inches from the left hand side of the right back post is placed a friction pulley, about two inches and a half in diameter; running with iron gudgeons in poppet heads of horn and leather mortised into the two roves last described, and constructed in the same manner as those in which the spindles run. There need not, however, be more than one sized small hole bored from the under side of the roves, reaching the mortises, through which holes the leather stems, or tongues of the poppet head, pass and are fastened by a pin driven through them in the rovers; nor need there be any circular leathers, as in the poppet heads of the spindles, at a distance of five inches and a half from the centre of the first mentioned friction pulley; and to the left side of it is placed another similar friction pulley and fastened in the same manner; and friction pulleys are placed and added on in the same manner to the left, according to the number of spindles for which the machine is intended; that is to say, three friction pulleys for eight spindles, four for ten, and five for twelve, and so on for any contemplated number of spindles.
The machine is banded in the following manner, commencing at the main wheel, or wheel first described, which gives motion to the spindle wheel, a cotton or woollen round band is placed around the rim of the main wheel and passing round the forward ends of the hub of the spindle wheel, in the groove cut and turned therein as above described; around the rim of the spindle wheel is placed a similar band passing up from the right side of the spindle wheel through the two roves and passing over on the right side of the two right hand spindles, then down around the first right hand friction pulley, and on the right hand side of it, then up and over the whirls of the two next spindles, and on the right side of them as before, and so on until you come to the last spindle, when the band, instead of going directly down to the left side of the spindle wheel, is turned over the right side of the last friction pulley, and then on to the rim of the spindle wheel.
About four inches back of the front posts, are placed on the top of each plate, a small column or post, about three inches high, into the heads of which are inserted in round holes or mortises the end of a wooden rod, of about an inch in diameter, extending from one to the other; to these rods are affixed the usual guide wires poised by weights and applied in the usual manner, to guide the yarn on the spindles on the inside facing, each other, and for the whole length of the front posts, wood or metallic tongues project, or a groove is cut, on which, according as pulleys or ears affixed to the brake or gripe are used, move up and down; the brake or gipe is intended to hold the rolls, and is constructed and poised in the manner long in use. The sliding gauges are inserted in each front post, in the usual manner.
To construct a machine for twelve spindles, the distance between the back posts and the distance between the front posts, together with the timbers affected by those distances, must be proportionably increased. The number of pulleys increased to five; then the band on the right hand side of the spindle wheel must pass through the roves on the left hand side of the right friction pulley, up the right side of the whirl of the right spindle, then over and down as before until it comes to the last left friction pulley but one, over which passes the band on the left side of the spindle wheel in the same manner as in the machine for eight spindles, instead of passing in that manner round the last left friction pulley.
To construct a machine for twenty-four spindles, enlarge the distances and proportions as before, add another spindle wheel to receive its motion from the first spindle wheel, and then band the additional twelve spindles from the second spindle wheel, in the same manner as in the twelve spindle machine; and on this principle the machine may be geered and banded to suit any required number of spindles.
The bands are fastened or closed by a wire hook and eye, and may he tightened or loosened by unhooking them, and either Original from NEW YORK PUBLIC LIBRARY
PLATE 25
twisting or untwisting them as the case may require, and hooking them together again.
On the upper side of the rails on which the spindles are adjusted, a piece of wood the length of the rails, between the plates into which they are mortised, half an inch thick and as wide as the rails, may be screwed on for the sake of neatness of appearance, if the mechanic please.
The mode of spinning or roping, is the same as in other vertical spinning machines.
The specific new and useful improvements herein before described and claimed by me, as the inventor, are the following:
First, the raw hide rims of the wheels.
Second, the manner of placing and applying the friction pulleys, so as to produce equality of bands and diminish friction, as above described.
Third, the peculiar mode of communicating motion to the spindles, by arranging, geering, and banding the wheels, friction pulleys and spindles, as above described.
Fourth, the peculiar mode of banding the spindles, as above described.
The advantage of this machine over all others for the same purpose, is, the simplicity of its construction, its less liability to get out of repair, the great diminution of friction, and the steadiness and equality of the motion of the spindles.
JOHN W. WHEELER
EDMUND W. JENNINGS,
ORAM GRAY OTIS.
Witnesses.
Patented October 11, 1828.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, vol. 6 (1828), p. 398 · View the page
19. Spinning and Roping Cotton and Wool, by a machine called the "Complete Spinner;" John W. Wheeler, Galway, Saratoga county, New York, October 11.
Remarks. This is one of the machines commonly called "Domestic Spinners;" and is intended to run from eight to about twenty-four spindles. These are all, of course, modifications of the larger machines used in cotton and wool factories. In this instrument, the rims of the band wheels are directed to be made of strips of raw hide, formed, whilst wet, upon wooden moulds, and allowed there to dry and become hard. The collars, or poppet heads, as they are called, of the spindles, are directed to be made in a peculiar way, of leather, and of horn. A particular mode of tightening the bands is designated, and there are some other variations in the arrangement of the parts. The claims of the patentee, are as follow: "1st. The raw-hide rims of the wheels. 2nd. The manner of placing and applying the friction pulleys, so as to produce equality of bands, and diminish friction. 3d. The particular mode of communicating motion to the spindles, by arranging, gearing, and banding the wheels, friction pulleys, and spindles. 4th. The peculiar mode of hanging the spindles."
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The specification was printed in the Mirror of the Patent Office (1828).
- Burke's 1847 Patent Office list gives the same patent.