Drawings and documents
Published accounts: specification
Specification printed in the Journal of the Franklin Institute
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 380 · View the page
Text of the specification as printed in the Journal, from OCR; not proofread.
Specification of a patent for an improvement in the construction and application of Friction Rollers. Granted to DAVID BALDWIN, of Queensbury, in the county of Warren, and state of New York, October 1, 1830. THE friction rollers which have hitherto been applied to the gudgeons of heavy wheels, or to the axles of carriages, have generally been constructed as follows. A number of cylindrical rollers of cast iron or brass, are connected to a flat ring at each end, by an arbour passing through each roller being rivetted to these rings. The rollers are then fitted to a hollow cylindrical metallic box, the inside of which is smoothly finished, so that the rollers may roll freely around its internal surface: a cap is then fitted to each end to keep the rollers in their place; perforations being left sufficiently large to permit the rings to which the rollers are rivetted to revolve freely within them. This box of rollers is then put upon the axle, or gudgeon for which it is intended. The objection to using rollers thus constructed, is, that it is difficult to tighten them when worn; which will soon happen if used in heavy work. To obviate this difficulty is one of the principal objects of the present improvement. My improved rollers are constructed in the following manner. The middle portion of each roller is cylindrical, but the two ends are in the form of the lower fructrum of a cone, with the bases applied to the cylindrical portion, and of the same diameter. The rollers are connected to each other by a ring at each end in the common method. The box in which they run is shaped on the inside to correspond with the shape of the rollers. The straight, or cylindrical part of them, however, is not permitted to touch the inside surface BALDWIN'S Friction Rollers. of the box, a slight enlargement being made therein for that purpose. The rollers then touch the box only on the slant side of their conical ends, and it will readily be perceived that if they wear, they can be tightened, if the upper and lower parts of the box can be brought nearer together, and that this may be done, I construct the box in the following manner. In the first place, let the box be made a perfect hollow cylinder, as in the old method, a little larger than is necessary to receive the rollers which must be placed within it. There will then be a space between the tapering ends of the rollers and the inside of the box, which must be filled up. Let a casting be made to fill this cavity, and fitted so that it may be put in and taken out at pleasure; and from around the upward portion of this casting, let a circular flanch project outwards, so that its outward edge may correspond with the outside of the cylinder, and its bottom may be brought in contact with the cylinder's upper surface. (The terms upper and lower are here employed with reference to the position of the box when used for a grist mill spindle, or any other perpendicular shaft.) Let two screws pass through this flanch into the cylindrical box, which is tapped for their reception opposite each other; that is, one screw on each end of a diameter of the cylinder. Let another diameter be drawn at right angles with the first, and at each end place another screw, the female part of which is within the flanch, and its blunt end pressing upon the edge of the box. The first mentioned screws will draw the two nearer together, and the others will separate them, so that by these screws they may be made loose, or tight, at pleasure. Connected with this flanch, and in the same place, another flanch projects inwards as far as may be, without interfering with the rings to which the rollers are fastened, the object of which is merely to keep the rollers steady. Both ends of the box may be fitted in the manner above described; or the lower portion of the box may be made to fit the taper of the rollers. A flat ring screwed to the bottom as above described, with an elevation from its lower surface for the rollers to rest upon, will serve to raise or lower them, as may be required. The rollers and boxes may be made of any metal sufficiently hard, whether cast or wrought, but for heavy work, I prefer cast iron. Another improvement which I believe to be new and useful, is the application of friction rollers to the spindles of grist mills. It is well known that it is somewhat difficult to bush a spindle properly. If made too loose, it will not run steadily; if too tight, it will soon heat. My method of applying the rollers to the spindle, is simply to fit them accurately to it, and to wedge the box which contains them, into the eye of the lower stone. The grain is kept from falling into the box by a leather collar fitted to the spindle, as has been formerly practiced. What I claim is the making of a portion of each end of the rollers tapering, that they may be tightened, as above described; and the application of friction rollers to the spindles of grist mills. DAVID BALDWIN. HAWLEY'S Wheat Fan. Description of the Section. A, A, section of the hollow cylindrical box to receive the rollers. B B B, B, a short cylinder, the outside of which will fit the inside of the box A, and the inside just receive the tapering ends of the rollers. E EVL C, C, the bottom of the box A, A, attached by screws in the same manner with the upper portions A D B, B. D, D, sections of two of the rollers, the gudgeons of which are rivetted to the rings at E, E, E, E. F, a spindle within the rollers. کے C A F D L C
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 5 (1830), p. 31 · View the page
22. For a machine for Scalding and Napping Hats; Daniel Baldwin, Ithaca, Tompkins county, New York, October 15.
Remarks. The machine described is a sort of box, to be placed over a planking kettle, or large boiler. At the top of the box is a pulley, worked by a rope, for the purpose of letting from ten to fifty hats at a time descend into the heated liquid, or drawing them up at pleasure. There, of course, is no bottom to the box, and the hats are contained in a cloth suitably fixed for the purpose, and which, with other parts, is particularly described in the specification.
About this record
- Patentee
- the Journal of the Franklin Institute, Journal
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The patentee's full name comes from the Franklin Institute's journal.
- Burke's 1847 Patent Office list gives the same patent.