Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 374 · View the page
37. For an improvement in the mode of Separating Gold, and other Precious Metals, from the earths and stones with which they are often found combined, called "Vibrating Cylindrical and Circular Troughs;" Roswell King, M'Intosh county, Georgia, October 1.
Remarks. This machinery consists of a trough which is a longitudinal segment of a cylinder, of about 10 feet in length, and 3 in diameter, and of a circular trough, of about 5 feet in diameter, and 6 inches deep, with their appurtenances. The cylindrical trough, or cradle, is made to incline a little towards one end, and it is separated into compartments, by several partitions, reaching across it, but, (we suppose,) leaving an open space between their lower edges and the trough. The earth to be washed is put, with water, into the upper division, and a vibratory motion is given to the trough; or the contents are agitated by means of a vibrating bar placed above the trough, from which dashers project down between each of the divisions. The earth is thus to be washed off, and the gold collected at the lower end of the trough. The circular vibrating trough is sometimes added to the cylindrical one, and is used to receive the materials which have been partially washed in the cylindrical trough; it then completes the operation. This trough is placed horizontally, with an iron axle in its centre; a vibratory motion is to be given to it by means of a crank, and the waste matter runs off at a spout, or an opening in its rim. The invention claimed, is the before described mode of separating gold, &c. and the machinery by which it is accomplished. We need not here repeat the observations made on No. 28, but think that they apply to each of the machines described.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 379 · View the page
The centre of this horizontal wheel, or table, is to be under the partition wall which divides the two ovens, at a distance above the top of the wheel, or table, sufficient to pass the glass under, so that the glass placed upon, and flattened on the stone, on the half of the wheel, or table, in the flattening oven, may be carried around upon this table which revolves on its centre, under the said wall, to the cooling oven, without taking it from the stone until it arrives in the cooling oven, and then, when sufficiently cool, to be placed away; at the time the wheel, or table, is stopped revolving, and the glass upon it is cooling and taken off in the cooling oven, after having been conveyed upon it, from the flattening oven, another cylinder can be flattened on the stone on the other half of the wheel, or table, that has passed by its revolution from the cooling to the flattening oven. By this operation it does not require that the glass should be removed from the stone upon which it is flattened, which preserves the polish, and prevents the surface of the glass from being scratched, which is the case when it is pushed over the surface of the stones, from the one to the other. It also differs from the other mode, in this, that by the revolving of this wheel, or table, the stones are both made flattening, and both cooling stones, or the whole wheel, or table, is both a flattening and cooling stone. WILLIAM COFFAN, Jr. Specification of a patent for a Rail-road Car. Granted to JOHN ELGAR, of Baltimore, Maryland, October 1, 1830.
Remarks. To obtain a form and combination of substances that will reduce the friction in the rubbing parts of a rail-way car, to its lowest point, where the "friction wheels" are not used, I adopt the admirable plan of outside journals, introduced and patented by R. Winans. The essential advantage of which, is, that the journals are reduced onethird in diameter (of course the friction is equally reduced) still preserving the full size and strength of the axles between the wheels. The axles extend through the wheels, about 4½ inches, are steeled, and turned to 2 inches diameter, and hardened, which forms the journal. To this journal I adapt a bearing, or box of cast iron, either in two pieces, or one entire piece; and to obtain an opening in the box that shall at once combine a proper shape to fit the journal, with a smooth and excessively hard surface, it is cast upon a "chill," or piece of iron dressed to the size of the journal, but with three ribs upon it, running lengthwise, which divides the circular BALDWIN'S Friction Rollers. opening of the box into three parts, and reduces the bearing on the journal to one-fourth of its circumference. In the contact of substances so hard, this quantity of surface is sufficient, and the friction is less. The back part of the box is at the same time chilled, for the purpose of receiving against it the steel centre point of the journal, that the tendency to lateral motion may be governed, without the friction consequent upon shoulders. To exclude dust, and confine the oil, I use a packing plate, similar to that which is used at the piston stem of the steam engine. This plate passes on the journal in front of the box, and is screwed up to the latter, with packing of hemp, leather, or cork. The side, or face of the plate toward the wheel, has a projecting flanch upon it, which embraces the hub and excludes the dirt. The box will perhaps contain one half gill of oil beside the journal, which insures a perfect lubrication of the latter.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 380 · View the page
The improvement that I claim as my invention, is the chilled, cast iron box, combined with the steeled, centre pointed journal; the peculiar form of the inside of the box, which reduces the surface of the bearing, and the packing plate. JOHN ELGAR. Specification of a patent for an improvement in the construction and application of Friction Rollers. Granted to DAVID BALDWIN, of Queensbury, in the county of Warren, and state of New York, October 1, 1830.
Remarks. THE friction rollers which have hitherto been applied to the gudgeons of heavy wheels, or to the axles of carriages, have generally been constructed as follows. A number of cylindrical rollers of cast iron or brass, are connected to a flat ring at each end, by an arbour passing through each roller being rivetted to these rings. The rollers are then fitted to a hollow cylindrical metallic box, the inside of which is smoothly finished, so that the rollers may roll freely around its internal surface: a cap is then fitted to each end to keep the rollers in their place; perforations being left sufficiently large to permit the rings to which the rollers are rivetted to revolve freely within them. This box of rollers is then put upon the axle, or gudgeon for which it is intended. The objection to using rollers thus constructed, is, that it is difficult to tighten them when worn; which will soon happen if used in heavy work. To obviate this difficulty is one of the principal objects of the present improvement. My improved rollers are constructed in the following manner. The middle portion of each roller is cylindrical, but the two ends are in the form of the lower fructrum of a cone, with the bases applied to the cylindrical portion, and of the same diameter. The rollers are connected to each other by a ring at each end in the common method. The box in which they run is shaped on the inside to correspond with the shape of the rollers. The straight, or cylindrical part of them, however, is not permitted to touch the inside surface BALDWIN'S Friction Rollers. of the box, a slight enlargement being made therein for that purpose. The rollers then touch the box only on the slant side of their conical ends, and it will readily be perceived that if they wear, they can be tightened, if the upper and lower parts of the box can be brought nearer together, and that this may be done, I construct the box in the following manner. In the first place, let the box be made a perfect hollow cylinder, as in the old method, a little larger than is necessary to receive the rollers which must be placed within it. There will then be a space between the tapering ends of the rollers and the inside of the box, which must be filled up. Let a casting be made to fill this cavity, and fitted so that it may be put in and taken out at pleasure; and from around the upward portion of this casting, let a circular flanch project outwards, so that its outward edge may correspond with the outside of the cylinder, and its bottom may be brought in contact with the cylinder's upper surface. (The terms upper and lower are here employed with reference to the position of the box when used for a grist mill spindle, or any other perpendicular shaft.) Let two screws pass through this flanch into the cylindrical box, which is tapped for their reception opposite each other; that is, one screw on each end of a diameter of the cylinder. Let another diameter be drawn at right angles with the first, and at each end place another screw, the female part of which is within the flanch, and its blunt end pressing upon the edge of the box. The first mentioned screws will draw the two nearer together, and the others will separate them, so that by these screws they may be made loose, or tight, at pleasure. Connected with this flanch, and in the same place, another flanch projects inwards as far as may be, without interfering with the rings to which the rollers are fastened, the object of which is merely to keep the rollers steady. Both ends of the box may be fitted in the manner above described; or the lower portion of the box may be made to fit the taper of the rollers. A flat ring screwed to the bottom as above described, with an elevation from its lower surface for the rollers to rest upon, will serve to raise or lower them, as may be required. The rollers and boxes may be made of any metal sufficiently hard, whether cast or wrought, but for heavy work, I prefer cast iron. Another improvement which I believe to be new and useful, is the application of friction rollers to the spindles of grist mills. It is well known that it is somewhat difficult to bush a spindle properly. If made too loose, it will not run steadily; if too tight, it will soon heat. My method of applying the rollers to the spindle, is simply to fit them accurately to it, and to wedge the box which contains them, into the eye of the lower stone. The grain is kept from falling into the box by a leather collar fitted to the spindle, as has been formerly practiced.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 381 · View the page
What I claim is the making of a portion of each end of the rollers tapering, that they may be tightened, as above described; and the application of friction rollers to the spindles of grist mills. DAVID BALDWIN. HAWLEY'S Wheat Fan. Description of the Section. A, A, section of the hollow cylindrical box to receive the rollers. B B B, B, a short cylinder, the outside of which will fit the inside of the box A, and the inside just receive the tapering ends of the rollers. E EVL C, C, the bottom of the box A, A, attached by screws in the same manner with the upper portions A D B, B. D, D, sections of two of the rollers, the gudgeons of which are rivetted to the rings at E, E, E, E. F, a spindle within the rollers. کے C A F D L C Specification of a patent for an improvement in the machine for cleaning wheat of every description, commonly called the Wheat Fan. Granted to WILLIAM C. HAWLEY, Brookfield, Fairfield county, Connecticut, October 1, 1830.
Remarks. BE it known, that my improvement in the wheat fan is as follows. Beneath the hopper into which the grain, or other seeds, are put, for the purpose of being operated upon by the machine, is placed a revolving cloth, or apron; the cloth (so called) may be made of leather, canvass, or other suitable material; and, of itself, forms the bottom of said hopper, upon which the seeds, or grain, may rest. Upon one of the rollers around which the cloth passes, and upon the end of said roller, is fixed a pulley, or band wheel, of eighteen inches diameter, more or less. Upon the end of the same roller is fixed the crank by which the machine is put in motion. A pulley is also fixed upon one end of the fan wheel's el's shaft, of six inches diameter, more or less, from which a band passes to, and around the eighteen inch pulley before mentioned.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 389 · View the page
The friction, or tension, requisite to wind the yarn upon the bobbin, is produced by the upper edge of the check over which the yarn is drawn, or compelled to pass at every turn of the spindle. The check is a thin piece of metal, bent flatwise, forming a curve corresponding with a circle less in diameter than that of the ring. It is fastened to a knee that is bolted, or otherwise fastened, to a fixed bar, or rail, that stretches along the spinning frame, back of the spindle. By means of a slot, or mortise, in said knee, the check can be raised or lowered at pleasure, carrying its upper edge more or less above the bottom of the connecting ring, and producing more or less angle in the yarn; consequently, increasing or diminishing the friction, or tension of the yarn, and winding it more or less tight on the bobbin. Said check should extend half way round the bobbin, though a greater or less proportion may answer the purpose. Small polished notches, or protuberances, on the upper edge of the check, will produce an increased tension on the yarn. The yarn passes down on the outside of the connecting ring, or lower edge of the cap, then up between said ring and the check, and over the upper edge of the check to the bobbin. Among the several improvements above described, there is but one in which I claim an exclusive property, and that is, the check, as above described, by which the progress of the revolving yarn is obstructed, the yarn made to fall back of the cap, and to wind on the bobbin. JOHN THORP. References to the Plate of J. Thorp's improved Running Cap Spinner. A, the spindle. B, the cap. C, the connecting ring. D, the box that forms the upper bearing E, the step in which the spindle stands. F, the bobbin. of the spindle. G, the head or collar on which the bobbin stands. H, the tube on which the bobbin loosely turns. I, I, the check, that obstructs the revolving progress of the yarn, causing it to fall back of the cap, and wind on upon the bobbin. J, J, two lips on the spindle, formed by soldering two pieces of wire to it. They slide in the two channels formed in the bobbin or tube, causing the bobbin to turn with the spindle. K, the whirl. L, a collar that slides loosely on the spindle. From its perforation two lips project inward, and into the channels in the spindle, by which the collar is made to turn with the spindle. The bobbin sets on this collar, and the friction of its base on the collar gives motion to the bobbin. This collar, as well as the head or collar of the tube, H, sets on the vibrating rail or lifter of the common throstle frame, and moves with it to distribute the yarn on the bobbin. M, M, one of the channels or grooves in the spindle. The other is directly opposite to it. In altering spinning frames now in use, or those where the spindles are small, it would be better to use the lips, rather than the channels, as the latter would weaken them. In building new spinning frames, the spindles can be made enough larger for that purpose. They both work equally well. The yarn is represented as passing through the loop above the spindle. Fig. 3, represents the check. This will answer a good purpose in making cotton roving, &c. Specification of a patent for an improvement in the Stock and Hand Vice. Granted to ENOCH D. M'CORD, of the Village of Sandy Hill, in the county of Washington, New York, October 1, 1830.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.