Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 6 (1830), p. 376 ยท View the page
43. For an improvement in the Distillation of Grain into Whiskey, of which Indian Corn is the principal ingredient; Dan Samson, Perrysburgh, Cataraugus county, New York, October 1.
Remarks. The patentee gives directions respecting the quantities of the different kinds of meal, and of water, that are to be mixed together; the degree of heat to be given to the mixture, and the time which should elapse in the different intervals; but after being very definite, he gives great latitude; which, as his patent is based upon these particulars, appears to render the whole unstable. We will give one example, as a specimen of the whole. "Then stir the mash well, and cover the tub, and let it stand one hour; the time, however, may be varied from 2 to 3 hours." After this he claims "the quantity and heat of water mentioned." "The length of time the mash stands from the time the corn meal is put in, before the rye meal and malt are put in. The length of time the beer stands before running. The small quantity of English grain to the corn," &c. &c. [TO BE CONTINUED.] SPECIFICATIONS OF AMERICAN PATENTS. Specification of a patent for a new mode of combining the power of the Lever and the Pulley, in the Standing Press. Granted to GEORGE W. GRATER, of Boston, Massachusetts, October 1, 1830, and assigned by him to LEMUEL BLAKE, of the same place. To all whom it may concern, be it known, that I, George W. Grater, of Boston, in the state of Massachusetts, have invented a new mode of combining the powers of the lever and the pulley, in the standing press, for pressing articles of various kinds; which press is intended to be used as a substitute for the ordinary lever, screw, and hydrostatic presses; and that the following is a full and exact description of the same. I make a strong frame, which may consist of cheeks, properly united by cross pieces, with mortises and bolts, in the manner common in screw presses; or, instead of cheeks, I use four strong corner posts, mortised into sills, and having such cap and cross pieces, or ties, framed into them, as may be deemed necessary. This latter mode I prefer, and it is the one which is represented in the drawing deposited in the patent office. The bed of the press I usually place near the upper part of the frame, or cheeks, bolting, and otherwise securing it firmly thereto; the follower being suspended below, by the tackle, in the manner to be presently described. Across the top of the frame, or cheeks, and extending from side to side, I affix a strong iron axle, turning upon gudgeons, in suitable boxes; upon this axle, and usually near its middle, I place an iron toothed wheel, and on each side of this wheel, cylindrical pieces of wood, or other material, around which the rope to be used is to wind in the operation of the press. A second axle is placed parallel to the former, having upon it a pinion or small toothed wheel, which takes into the former; there is also fixed upon this axle, a round block, or hub, with mortise holes, to receive the end of the lever, or hand spike, which is to operate upon this compound windlass. Ratchets and palls are employed in the usual manner. each end of the bed, and of the follower, and attached thereto, I place two, three, or more sheeves, or pulleys; the ends being notched out to receive them, and a bolt upon which they are to turn, passing through, or on one side of the bed and follower. For the purpose of obtaining the greatest strength, it will be best to secure these bolts, by staples, on the upper side of the bed, and on the lower side of the follower, instead of passing them through their substance. At The press, as before described, is now ready for the reeving of the rope, which is thus effected. A single rope is taken and passed under the follower towards the back part thereof, the two ends being brought up through openings left in the ends of the follower for that purpose; they are then passed over the two back pulleys of the bed, and under the two of the follower, and successively around the reVOL. VI.-No. 6. - DECEMBER, 1830. 48 maining pulleys, until they pass up from the last pulley on the front of the follower; the two ends are now secured, one on each of the cylindrical pieces of the first named axis, when the press is ready for use. In order to preserve an equal tension in the rope, that part of it which passes under the bed is sustained by friction rollers. The operation of the press is now manifest, as it is similar in principle to that of an ordinary tackle, operated upon by a windlass. In order to sustain any part of the articles in press at any required height, holes are bored through the cheeks, or uprights, into which rods, or pins, may be inserted, so that any part may be taken out and renewed without taking out the whole.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The Franklin Institute's journal spells the name differently.
- Burke's 1847 Patent Office list gives the same patent.