Drawings and documents
National Archives restored drawings: drawing
Robert McCormick's Patent Drawing for a Machine for Breaking Hemp and Flax
National Archives, Restored Patent Drawings (Record Group 241) · Full-size scan at the National Archives · Catalog record
Show the text on the drawing Hide (150 words)
Words on the drawing as machine-read by the National Archives; not checked. Useful mainly for searching.
13. BRAKES & GINS. / Reciprocating Brakes. / $20 / Topview of bant frame / Probert Me Cormick. / Air.1. / Machine for breaking Hemps Hax. Vol.10 271. / CLASSIFICATION / Patented bet 1. 1830. / 6145-4 / DIVISION. / References. / the Bed of bars. / abture plane angles. / a"a" acute angle. / b. / a"a" a" flate fars. / fluted Bocker. " side pieces. / Da upright posts. / e Toppiece. / of vibrating bar / I bar / h. bant Frame see Jy.3. / i.iii loose pins. / Kh.KK springs. / lill pins. / Sigh Dent lever, pring / ferew. / m m mm straps. / n.n bent levers. / 'o.o. 1 crews. / to feeding apron / q delivering apron. / z.z. weights. s.s. blocks. / Patent office March 11 1842. / made under the direction of the Commissioner / of Patents in conformity with act of 3ro march 1837. / ML Ellmorth / Commification of Patents / Jiy.2. Section / Ch.I. Fleischmann first.
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (859 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 1.
6145X
R. McCORMICK.
Hemp Brake.
No Printed Specification Available
Patented Oct. 1, 1830.
N. PETERS, Photo-Lithographer, Washington, D.C.
Page 2.
Oct. 1 1830 645x 271.
Robert McCormick
Patent Date October 1, 1830.
The Certificate referred to in these Letters Patent is a making part of the same containing a description in the words of the said Robert McCormick himself of his improvement in the machine for breaking hemp & flax.
It is to be known that Robert McCormick of Rockbridge County State of Virginia have made an improvement in the machine for breaking hemp & flax which is described as follows. This machine consists of the following five simple parts: 1st The frame. 2nd The bed of bars. 3rd The fluted rocker. 4th The upright posts & top piece. 5th The vibrating bar.
1st The frame is about 2½ or 3 feet high, about 5 feet long, 5 feet wide, and of sufficient strength to support the machinery to be hereafter described.
2nd The Bed of bars. This bed of bars consists of about 9 pieces or less, the tops of the 3 in front are made with obtuse plane angles, the next 3 are at an acute angle at top & angular at the shoulders, the next are flat at top about 9½ inches wide with angles at the shoulders, they are disposed in such a way as that when the hemp or flax enters it is slightly crushed; the second set break it still further & the 3 last complete the operation of breaking. They are made of cast iron 1¼ inch thick & placed apart at about 2½ inches across the frame. They may also be made of wood in the same manner but proportionally strong.
3rd The fluted Rocker is made of cast iron or cast steel, being a segment of a circle of about 3½ feet radius, the flutes are made to correspond with the bed of bars before described. It is secured to two rockers made of wood, one on each side & the sides are connected by a frame. The ends of the rockers extend beyond the bed of bars about 7 or 8 inches. The upright posts & top piece. These are two upright posts about 4 feet high & formed into the rockers one on each side. A top piece connects these posts by being mortised & tenoned into them.
5th The vibrating bar is made of iron,
Page 3.
Waylands between the posts across the frame it turns 2 or 3 on wagons in the straight path & it has a hole mortise in its middle to admit a bar 6 ft. The cant frames & levers. The cant frame consists of thin heavy wood one between each two of the bed bars connected together by a piece of wood at each end of the bars. In the frame where the points of the cockers strike are long pins one at each corner, which are pushed down by the motion of the cockers & are attached to the springs below the frame. These springs act one fulcrum & push up the cant frame by means of other pins near the center. The cant frame is prevented from rising too high by means of straps connected with it & the main frame. There are two bent levers one on each side from which the cant frame receives its motion backwards & forwards. These levers are attached to springs thru which two long screws extend down thru the frame. The tops of which screws are operated on by a projection attached to the cocker yds. The feeding & delivering aprons. These are made similar to those used in threshing machines & receive their motion from a cage wheel operated on by the levers which work the cant frame. Operation. The hemp being first properly fixed frame it is laid upon the feeding apron, a sufficient weight is attached to the top & upon the upper part of the fluted rocker, a bar or driver is put thru the vibrating bar one end of which may be attached to any machinery that will give it a vibratory motion. Motion being given to the machine the hemp is crushed between the fluted rocker & bed of hay. The cant frame & levers being operated on by the cocker carry forward the hemp about 2 inches at each vibration till it is completely broken & delivered upon the hinder apron. The cocker is kept in its place by blocks of wood grooved out to receive ends of the rocking frame. What is here claimed as my invention is the whole of the before described machine for breaking hemp & flax. For a further illustration of my invention I refer to the model & drawing of the same deposited in the Patent Office. In testimony that the foregoing is a true description of my invention I have subscribed my name before two witnesses at the City of Washington this 27th day of July 1830.
William P. Bell
Witnesses:
Lyman H. McConnel
Arthur W. Coombs
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.
Shaw: lists McCormick, R. here as 6145½