Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 9 (1832), p. 318 · View the page
It appears, judging from the drawing, if such it may be called, that this is intended as a domestic spinning machine, as it is represented as carrying eight spindles only. The band which drives the spindles appears as though it pressed against their whirls, which it is made to embrace by being carried round a roller between each spindle, a, a, a, being the spindles, and b, b, b, the rollers, which are, we suppose, what are designated friction wheels by the patenb a b a bb a a a tee. He claims "the putting any number of spindles in motion by one band, by the improvement of the friction rollers, consequently the yarn or thread on each spindle is twisted exactly even, or alike, which cannot be done with a band to each spindle." 22. For a Machine for Planing and Dressing Boards, &c. John W. Newberry, Avon, Livingston county, New York, November 15.
Remarks. The plane used in this machine has cutting irons fixed in the ordinary manner; but, being intended to cut by its motion in both directions, it has two irons which have inclinations the reverse of each other. The stock has two faces, the planes of which form an obtuse angle at their union in its middle. The plane is made to tilt as it passes backward and forward, so as alternately to bring each face, and cutting iron, on to the board or plank. There is a frame work above with cog wheels, and a rack and pinion, with their necessary appendages for working the sliding frame with the plane, back and forth. There are also proper contrivances for holding the board; the whole of these are well represented in the drawing which accompanies the specification, to which there are ample references. There is no claim made, and as the machine is not similar to any other for the same purpose with which we are acquainted, this may not be of any importance. From its structure, it appears to be calculated for short stuff only, and we think it too complex for general use, even for such stuff. In the greater number of cases, a plane of the ordinary construction, especially in roughing out, will tear the stuff in working in one direction, and indeed, the cases are rare in which even a smoothing plane may be used indifferently either way. This objection must lie against most of the planing machines in which the cutting is not done in a curve. 23. For a Self-regulating or Self-directing Rail-road Car; Lewis Wernwag, Harper's Ferry, Jefferson county, Virginia, No vember 15. This car is to have four wheels fixed in the usual way, and half way between these there is to be another pair of wheels of smaller diameter, which last, are the regulating, or guiding wheels. The fore and hind axles run in frames connected together by coupling poles, like those of a common wagon, but of equal length, so as to meet in the centre. The guiding wheels are to operate upon the coupling poles at their point of junction, forcing them laterally, according to the curvature of the road. In the drawing, these guiding wheels are represented as about four-fifths of the diameter of the main wheels. They are connected together by means of a slender iron axle, which has its main bearing in a box at its centre; there are shoulders upon the axle by which it is made to act upon the poles which are connected with the box, or bearing. The guiding wheels are furnished with flanches, like the main wheels, and when the road is curved, these flanches, touching against the edges of the rails, cause the ends of the coupling pole to keep in the centre between the two rails. There is a jointed lever attached to each side of the carriage, furnished with boxes to receive the axle of the regulating wheels, in order to steady it, whilst they allow it to slide freely endwise. The claim is to the described method of making rail-road carriages with self-directing wheels and axles, however applied. Where a road is considerably curved, the vertical edge of the flanch of the guide wheel, acting upon the vertical edge of the iron rail, will occasion much rubbing friction, which will cause them to wear with considerable rapidity. Should this objection prove to be of little moment, the principle upon which they act is undoubtedly good.
About this record
- Patentee
- Jim Shaw's X-patent list
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.
- Residence from Burke's 1847 Patent Office list; the standard lists give none.