Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 10 (1832), p. 35 · View the page
19. For a Valve for the Vibratory Steam Engine; Thomas Halloway, Northern Liberties, Philadelphia county, Pennsylvania, January 18.
Remarks. (See the specification.)
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 10 (1832), p. 42 · View the page
I intend, usually, to place the trunnions or gudgeons upon which the cylinder is to vibrate, at or near its centre; this, however, is not a point of importance, as my principle is equally applicable in all situations of the trunnions, or gudgeons. In one of the trunnions, or gudgeons, there are two openings made for the admission of steam into each end of the cylinder. In the box, pedestal, or bearing, of this gudgeon there are three openings, one of which is in the centre for the escape of steam, the other two are for the admission of steam into each end of the cylinder, respectively. These openings are so arranged that when the engine is at half stroke, they are all closed; and at or near the end of the stroke, one of the openings in the gudgeon is over one of those for the admission of steam, and the other over that for the discharge of steam. This arrangement will be distinctly seen by the aid of the drawings, and the references thereto, deposited in the patent office, and making a part of this specification. To prevent the raising of the cylinder from its bearing by the pressure of the steam, and to keep the gudgeon in proper contact with the pedestal, I apply a spring on the upper part thereof, or cause a friction roller to press thereon, or make use of any other device which I may prefer. Among other advantages of this arrangement is the dispensing altogether with packing, the facility of oiling, and the certainty of the valve always remaining steam tight. What I claim as my invention is the manner and principle of arranging the valves, or the openings for the admission and the discharge of steam, as hereinbefore described. THOMAS HALLOWAY. A patent was granted to Elisha Bigelow, of Baltimore, on the 6th of November, 1826, for a similar mode of letting the steam on and off in the trunnions of a vibrating engine, and there are others in which the same method is adopted, varying slightly in the mode, but acting essentially on the same principle. Specification of a patent for a Wing Gudgeon Valve for Steam Engines. Granted to THOMAS HALLOWAY, Northern Liberties, Philadelphia county, Pennsylvania, January 18, 1832.
Remarks. To all whom it may concern, be it known, that I, Thomas Halloway have invented an improvement in the valves of steam engines, which I intend to apply to locomotive operation only, and which is called the "Wing Gudgeon Valve," and that the following is a full and exact description thereof. I intend that the cylinder, or cylinders, to which my valves are applied, shall vibrate, in general, vertically, but this is not a point of importance, its position being governed by circumstances. The cylinder is to have one large gudgeon, close to which, above and below, is a face plate, or wing, with an opening leading to each end of the cylinder, longitudinally, which face is exactly in the shape of the segment of a circle, as is shown by a model and drawings, deposited in the patent office. The piece constituting the valve seats is cast about the width of the boiler, with a plate on each side corresponding with the face on the cylinder, and may be circular, or straight, according to the form of the top of the boiler. This valve seat has two distinct openings leading from a double division cock in the centre to the valve seats which the cylinder vibrates against, and passes out in two openings on each side, corresponding to the openings on the plate of the cylinder; and with the vibration of the cylinder it alternately receives and discharges steam. It will be understood by every competent engineer that both the face of the plate valve seat, and that of the plate on the cylinder, are to be turned perfectly true, and made steam tight, and will be kept up by a spring, friction roller, or weight. The cock, which has been mentioned, in the centre of this valve seat, and on the centre of the boilers, is to be so constructed that by turning half round, it reverses the power of the engine; that is, it makes the steam side the exhaust side, and vice versa; and it also answers to shut the steam from both engines: [qu. ends.] What I claim as my invention is the arrangement of the cylinders and valves to a locomotive engine; the mode of fitting the valves; the construction of the cock in the centre to determine the direction of the engine forward or backward; and the simplicity of the whole, not having half the number of pieces when completed that the generality of English engines have. THOMAS HALLOWAY. Fig. 1, is the face of that half of the valve which is cast on the cylinder, with openings leading through the steam ways to the two ends of the cylinder. Fig. 2. A circular plate forming the other half of the valve, faced to fit steam-tight on fig. 1. A, is an opening in it, to receive the trunnion or gudgeon B, fig. 1. WOODCOCK'S Self-Sharpening Plough.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The Franklin Institute's journal spells the name differently.
- The Franklin Institute's journal gives a different date.
- Burke's 1847 Patent Office list gives the same patent.