Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 10 (1832), p. 234 · View the page
11. For a Spiral Flanched Shell, to be used as a substitute for the ordinary Bomb Shell, or Howitz; William B. Pier and Andrew Mask, Detroit, Wayne county, Michigan Territory, April 6.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 10 (1832), p. 253 · View the page
Patent for an improvement in the Science of Gunnery, which may be used as a substitute for the ordinary Bomb Shell, or Howitzer; and which may also be substituted for the ordinary cannon shot or musket ball, and ejected from guns of any size or calibre. Granted to WILLIAM B. PIER and ANDREW MARK, city of Detroit, Wayne county, Michigan Territory, April 6, 1832.
Remarks. The patentees denominate their invention an "elongated spiral flanched shell," and an "elongated spiral flanched shot." The PIER and MARK'S Bomb Shell. first is named from its peculiar form, and is to be cast of such size as shall adapt it to the ordinance from which it is to be projected. For the sake of ready description, a shell adapted to a three pounder is taken as an example. Its form, without the flanches, is that of an elongated egg, with the small end truncated, or cut square off. The length of the shell may vary from one and a half to two or more diameters of the bore of the piece from which it is to be fired. The reason of varying the length is to allow of a larger cavity in certain cases, where it may be required. When the cavity is large, and the shell consequently thin, it is elongated in order to give to it the necessary weight. The large, or forward end, which nearly fits the calibre of the piece, is a solid hemisphere of metal, the weight of which will insure its keeping the proper direction when fired from the piece. Wings, or flanches, are cast upon the outside; of these there may be four, or more, they extend from the small end of the shell, to the swell of its hemispherical end; their direction is oblique, as they are designed to give to it a rotary motion like that of a rifle ball. Those edges of them which strike the air, are at right angles to the body of the shell, and they extend out therefrom, so that their exterior edges shall every where fit the bore. The angle which they make with a longitudinal section of the shell may vary from five to twenty degrees, more or less, as may be found best to answer the object intended. The diameter of the small or after end, may be reduced to one-third or one-half of that of the bulb or larger end, and the flanches, therefore, widen out in proportion. To charge the cavity of the shell, an opening is left either in the small end, or in the side between the flanches, through which the charge is to be introduced, and the opening then stopped with a screw, or a plug of wood or metal. The shell is to be made to explode by means of percussion power. For this purpose a hole is to be drilled through the larger end, or bulb, of the shell, in the direction of its axis. This hole may be from one-fourth to three-eighths of an inch in diameter until it reaches near to the cavity, when it is to be continued of such size only as may serve for a touch hole. An iron or steel bolt, surrounded by leather, or other elastic substance, is put over the percussion powder, and extends out from the front of the shell; its exterior end widens out like a nail or bolt head. This striking against any hard substance, occasions the contents of the shell to explode. The "elongated flanched shot" is similar in its external form to the shell, but as it is to be used as a shot merely, it has no cavity. When used for small arms it is to be cast of lead, to give it sufficient weight. The patentees say that its flight will be more rapid and its range greater than that of a round ball. Patent for machinery for Jointing Staves with a circular saw; and for Sawing Bilging Staves, by means of concavo-convex circular saws. Granted to PHILIP CORNELL, Brutus, Cayuga county, New York, April, 1832. For a full explanation of the particular construction of this machinery drawings would be required, a general idea of its construction may, however, be given without them. The jointing apparatus is intended for such staves as are straight upon their edges. The staves are held down upon a carriage by means of a lever, the adjustable bed of the carriage having such an inclination as that rake shall give to the edges of the staves which shall correspond with the size of the vessel to be formed; in this state the carriage is made to advance, carrying the staves against the edge of a circular saw. Several staves, placed one upon the other, are jointed at the same time. There is nothing new in the principle of this part of the machinery, the patent, therefore, is taken for the particular arrangement by which the operation is effected. For sawing barrel, or other bilging staves, a concavo-convex saw is made, which is a section of a sphere of such radius as shall adapt it to the bilge or curvature of the staves to be sawed by it. The staves are sawed one out of the other, either from plank or rived timber, of such thickness as the width of the stave may require. The carriage upon which the stuff to be sawed is fixed, has curved ribs, or guide pieces, taking into corresponding grooves in the bed upon which it runs, the radius of their curvature corresponding, of course, with that of the saw used. The carriage is driven forward by means of an endless screw, a rack and pinion, or other suitable contrivance. Sometimes an apparatus is used which joints the stave, giving the proper curvature and rake to the edges, at the same time that it is cut by the concavo-convex saw. This apparatus consists of two circular saws running on separate axes, and contained each in a sliding frame, governed by grooved guide pieces in such a way that as the stave advances against them they joint it in the manner described. We believe, however, that the machinery is rendered too complex by this addition, and that the patentee prefers to perform the operations separately. The patentee says: "What I claim as new in the before described machinery, and for which I ask a patent, is the apparatus for jointing straight staves several at a time, one edge only, by means of a circular saw, and giving to them the proper bevel, as herein set forth. I also claim the sawing of bilging staves by means of a circular concavo-convex saw, whether the same be done by using a carriage upon the construction set forth in this specification, or by placing the saw itself upon a moving carriage. For although I have described and represented certain frame work, and modes of communicating motion, I lay no claim to this particular arrangement of the accessory parts of the machinery." Specification of a patent for an apparatus for Holding and Guiding Edge Tools in the operation of Grinding. Granted to GEORGE A. MADEIRA, Chambersburg, Franklin county, Pennsylvania, April 19, 1832, To all whom it may concern, be it known, that I, George A. Madeira, of Chambersburg, Franklin county, Pennsylvania, have invented an apparatus, or machinery, for holding and guiding edge tools, and other articles in the operation of grinding, which apparatus greatly facilitates the said operation, and will enable an inexperienced hand to perform it with precision; and that the following is a full and exact description of the said apparatus. I use a spring pole, which is fixed along or near to the ceiling of the room or workshop, in the manner of those used for the pole lathe. The elastic end of this pole is directly over the grindstone, and from it descends a part which I denominate the hanger; the hanger is hinged or jointed to the spring pole, so that the angle which they make with each other may be varied. A brace passes diagonally from the spring pole to the hanger, a mortise being made through each for that purpose. This brace may be lengthened or shortened by means of pins, which pass through holes in it, and in the spring pole and hanger, and serve to confine them in any required position. In order to adapt the hanger to articles of different sizes and kinds, it is made capable of being lengthened or shortened; this may be effected by dividing it and making one part to lap over the other, or by a long slot in one piece, and a corresponding tongue on the other, with equidistant holes through them, and pins or screws to adjust or confine them. To admit of the article which is to be ground being moved backward and forward on the stone, there is a hinge, or rule joint, near the lower end of the hanger; and to allow of its transverse motion, the block upon the under side of which the article is to be held, is attached to the hanger by a hinge, or rule joint, in the reverse direction. The block must vary in its form and construction according to the nature and form of the article to be ground; and the articles may α e b 0 be held in their places by means of screws, wedges, or otherwise. No particular directions can be given for this part, nor is it necessary, as every workman can readily adapt the block to the particular purpose which it is required to answer. The block, is sometimes made with a handle projecting from each side of it, one for each hand. When axes, or other articles with eyes in them, are to be ground, the handle may pass through @ the eye, and form one part of the arrangement by which it is attached to the block. 0 0 SHULTZE'S mode of Bleaching Yellow Wax. I have thus described the manner in which I ordinarily form this apparatus; it, however, is susceptible of various modifications, whilst the general principle of its structure and action remains unchanged.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.