Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 11 (1833), p. 180 · View the page
Know all men by these presents, that I, John Ames, have made a new and useful improvement in the method of dressing pulp for the manufacture of paper by machinery, set forth and specified in the words following, viz:I construct a vat of convenient size, and insert therein a wirewound, hollow cylinder, constructed as follows; the skeleton, or frame work of the cylinder, is formed like the common wire cloth cylinder, with no more arms or interior work than are necessary to give strength and form to the cylinder. Instead of the wire cloth, a covering is formed by winding wire of a suitable size over the frame work, with interstices between the wires, of sufficient width for retaining knots, and allowing the dressed pulp to pass through. The cylinder is closed at one end and open at the other, with the open end closely adjusted to the side of the vat for conducting off the pulp, as is described in my patent method of " washing rags." I communicate to the cylinder a rotary motion. The pulp is admitted to the vat, and is dressed, or strained, by the wire covering. The knots, knobs, and other crude matter being retained, and the dressed pulp passing off through the open end of the cylinder to the vats, ready for use. In some cases it may be convenient to reverse the process by passing the undressed pulp into the cylinder, straining it so that the dressed pulp shall pass from the exterior of the cylinder, leaving the knots within. It may also be more convenient to conduct off the dressed pulp in the first described process, or to introduce the undressed pulp in the last, by means of a hollow arbor, with both ends of the cylinder closed, than by adjusting it as above described. An agitator of any sort may be inserted in the vat, for stirring up the pulp, (in the first described process,) if the action of the cylinder be not sufficient for that purpose. The improvement or invention that I claim specifically as mine, is the process or method of dressing pulp for the manufacture of paper, by using the wire-wound, hollow cylinder, or any hollow body, of any other figure, covered, or wound with wire, as above described, for that purpose. JOHN AMES. Specification of a patent for an improvement in the mode of setting Glazier's Diamonds, of all kinds. Granted to JOHN DICKENSON, city of Philadelphia, November 30th, 1832.
Remarks. I take the piece of metal in which the diamond is to be set, and drill a hole into it adapted to receive the handle, or shank, by which it is to be held; not, however, drilling it entirely through, but nearly so; I then take a smaller drill with which I perforate it completely. This leaves a shoulder upon which the diamond, or spark, as it is sometimes called, rests, when dropped into the larger hole, whilst its cutting point passes through, the hole being so adjusted as to allow it so to do. The diamond may be readily adjusted so as to present its cutting point in the best possible position, and it is to be secured there, without soldering, which may be effected in various ways; as, for example, by strong cement, which may be pressed upon it by means of the end of the shank, or handle, which I then pass into the hole prepared for it. The mode, however, which I usually adopt, is the following. I tap the hole which is to receive the shank, so as to form within it a female screw, the shank forming a male screw working freely in it; after dropping the diamond into its place, and adjusting it there, I take a small piece of some malleable metal, and drop upon it, when, by screwing the shank into its place, it is made to press upon the malleable metal, and the diamond will be fixed in a manner which is perfectly secure, whilst it is susceptible of alteration, or adjustment, at any time, with the most perfect facility. To the ferrule, or handle, I sometimes affix a piece of steel, or other metal, for the purpose of clipping corners, or strips, and removing narrow strips, which is commonly effected by a key, or a pair of pliers. This piece of steel, or other metal, has several notches made in it, of various widths, to adapt it to glass of various thicknesses.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 11 (1833), p. 316 · View the page
30. For an improvement in Saw Mills; David W. Hall, Sparta, Hancock county, Georgia, November 27.
Remarks. "The invention here claimed consists in the regulating screws, nuts and blocks by which the saws are kept at a proper distance apart; the bar, hooks, and screw-bolts for tightening the saws; the screwrods, nuts, and blocks, passing through the fender posts, and placed above the log to be cut, for stiffening the saws without making the saw gate so heavy as is common in order to accomplish this object;-and the cylindrical rods placed on the fender posts, with the small metallic slides on the saw gate by which the friction is reduced." The foregoing claim will point out, pretty clearly, to those well acquainted with saw mills, the general arrangement adopted by the patentee, and will show that it embraces very little of novelty in either of its parts. Guides for stiffening the saws have often been placed just above the log, and made adjustable, to adapt them to stuff of different sizes. The frames have also been made to work in metallic guides, instead of against the fender posts, and, in fine, nearly all the ends proposed in the present patent have been obtained by analogous means.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The Franklin Institute's journal gives a different date.
- Burke's 1847 Patent Office list gives the same patent.