Drawings and documents
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 13 (1834), p. 174 · View the page
8. For an improvement in the Escapement of Clocks; Orsimus R. Fyler, Bradford, Orange county, Vermont, September 6.
Remarks. (See the specification.)
Published accounts: specification
Specification printed in the Journal of the Franklin Institute
Journal of the Franklin Institute, new ser., vol. 13 (1834), p. 182 · View the page
Text of the specification as printed in the Journal, from OCR; not proofread.
Specification of a patent for an improvement in the Escapement of Clocks or Time Pieces. Granted to ORSIMUS R. FYLER, Bradford, Orange county, Vermont, September 6, 1832. To all whom it may concern, be it known, that I, Orsimus R. Fyler, of Bradford, in the county of Orange and state of Vermont, have invented an improvement in the mode of constructing the escapements of clocks, or time pieces, and that the following is a full and exact description thereof. Instead of using springs upon the pallets of verges, in the manner described by me in the specification of a patent for improvements in wooden and other clocks, granted to me on the 13th day of June, 1831, I apply a spring to act upon the pin, or arbor, on which the verge vibrates, in a way to be presently described; varying the same so as to adapt it to the particular construction of the pallets; or sometimes I give to the pin itself sufficient length to allow of its operating by its own elasticity, in such a manner as to effect the object which I have in view; my improvement consisting in the practical adoption of a principle, which may be variously modified. My usual method of attaching a spring to, or causing it to act upon, the pin, is as follows. I take two disks, usually of brass, which may be about an inch in diameter, and a line, more or less, in thickness; through each of these plates, or disks, I make a small hole, near to the periphery thereof, as shown at A, in the accompanying drawing. To one of the disks or plates, I attach a spring, which may consist of wire, coiled, or bent, in a serpentine direction, or made in any other manner. In the drawing, the spring B, is represented as serpentine, attached to the plate by one end; a loop, or eye, in the other embracing the pin upon which the verge socket turns. For a pendulum vibrating half seconds, and with a bob weighing about eight ounces, I have found wire No. 30, to be of a suitable size. To receive this spring, I make a hole through the front clock plate, nearly as large as the before named disks, one of which is to be attached on each side of the plate, so as to stand parallel to each other, with the holes for the pin coinciding, and a space between them forming a chamber for the spring. I then pass an elastic metallic pin, through the holes in the disks, which must be sufficiently large to allow it to have some play within them. One end of the pin has a swivel head, the other end being fitted to receive the verge socket. Sometimes I enlarge the hole in the outside disk, and support the FYLER'S Improved Escapement. outward end of the pin by means of a bridge placed outside of the socket of the verge; care being taken to make the aperture in which the pin rests, something larger than the pin itself. The verge and socket I construct in the way usual in recoil escapements, taking care that all the parts be made as light as can be eligibly done. The verge I usually allow to embrace about one-fifth of the circumference of the balance wheel, escaping in the common manner, taking care to place the pin which supports the verge, as near to the crown or balance wheel, as can be conveniently done, so that the recoil may be increased upon the horizontal pallets, and proportionably diminished upon the vertical section of the verge; the horizontal pallets being most relieved by the action of the spring, as is known to those scientifically acquainted with the subject. In fig. 2 of the drawing, the verge is represented as placed upon the pin, under the crown or balance wheel. The advantages of this mode of construction are, that the elasticity of the action of the pin, relieves the recoil, thereby producing a more free and easy motion, and admitting of finer teeth in the crown wheel; all the functions of the escapement will consequently be performed with less motive force, and with less oiling, than is required for common escapements. What I claim as my invention, and for which I ask a patent, is the principle of giving relief in recoil escapements, by means of an elastic pin, and likewise by coiled, spiral, or other springs, attached in such a manner as to support the pin, and to press it lightly towards the crown wheel. Fig. 1, represents one of the disks, having a hole in it at A, for the verge pin to pass through, and the bent spring B, fastened at the lower end to a pin, and with a loop at its other end to embrace the verge pin. In fig. 2, C, is the clock plate, D, one of the disks let into it, and having the spring B on its under side. E, a bridge to remove the pivot of the crown wheel. The dotted line re1 C E D 11 2. presents a piece of brass, which sustains the pin of the verge at its outer end. ORSIMUS R. FYLER.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847), the Journal of the Franklin Institute, Journal
- Burke's 1847 Patent Office list gives the same patent.