Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (773 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 2.
United States Patent
Patent No.: X8448
Henry Burden
Letters Patent
The schedule referred to in these Letters Patent and making part of the same, containing a description in the words of the said Henry Burden himself of his improvement in the construction of furnaces for the purpose of heating bar or other iron with anthracite and bituminous coal combined.
To all to whom these presents shall come. It is known that I Henry Burden of the City of Troy in the County of Rensselaer, and State of New York have invented a new and useful improvement in the construction of Furnaces for the purpose of heating bar or other iron with anthracite and bituminous coal combined, and that the following is a full and exact description of the construction, and operation of said furnace as invented by me.
The common method of constructing furnaces for heating bar iron with anthracite coal, is to make the furnace about three feet wide and four or five feet long with grates of this dimensions, with a sliding door in one end for the purpose of putting in the coal and iron, as also for drawing the iron out when hot. The grates are then covered with from three to four inches of Anthracite coal ignited on the top of which, the iron bars to be heated are laid, by shutting the door and drawing the damper, the iron consequently becomes heated proportionate to the heat of the furnace, but as there is no flame from anthracite coal to fill the space between the ignited coal and the arch, consequently a rush of air enters through the grates greater at some places than others, in consequence of their being more open or clear of ashes which often burns or melts the iron at spots while it is but partially heated at others.
Page 3.
United States Patent
Patent No.: X8448
In order to remedy this defect I am burning furnace about one foot longer than I should if using anthracite coal alone, with a door at each end of the furnace of similar dimensions and shape, I then proceed by putting a layer of anthracite coal on the grate of from three to four inches thick with the iron on the top in every respect as if I were to use anthracite coal alone as mentioned above. When the iron becomes heated sufficiently (or as hot as may be by the anthracite coal without burning at spots) I then open the door behind (as may be seen at fig. 1 of the accompanying drawings) and put in about one or two small shovel fulls of bituminous coal into the back part of the furnace (as may be seen at fig. 1 of the drawings) which immediately flashes into flame and moves along through the iron bars with great velocity on its way to the chimney as may be more distinctly seen at fig. 1 of the accompanying drawings. It will hereafter be discovered that the iron bars being completely immersed in one continued sheet of flame for a few seconds will become as hot as if laid on a sand bed and heated by flame altogether, as is done in the common reverberating or puddling furnace at an expense not exceeding one third that of bituminous coal or iron alone. The improvements which I claim are as follows. First by making my furnaces with a door at the back end so as to admit of the bituminous coal being put into the back part of the furnace as more fully explained by the drawings & specifications. Secondly By using the bituminous coal on a part of the grate at the back part of the furnace reserved for that purpose which gives the coal an opportunity of ignition (as well as could be by a reverberating or puddling furnace) before it comes in contact with the iron. The advantages of this method are great as may be more distinctly seen by the drawings & specifications. Thirdly - The improvement consists in combining the use of the anthracite and bituminous coal for the purposes of heating.
Page 4.
United States Patent
Patent No.: X8448
bar or other iron at the same time igniting each in separate
parts of the furnace as mentioned above and described by the
specifications and drawings annexed.
Witnesses
D. H. Stone
Justin Kellogg
Henry Burden
Patented October 14, 1844.
M. A. L. C.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 15 (1835), p. 321 · View the page
23. For a Furnace for Heating Bar Iron with Anthracite and Bituminous Coal combined; Henry Burden, Troy, Rensselaer county, New York, October 14.
Remarks. The patentee states that the common method of constructing furnaces for heating bar iron by anthracite, is to make them about three feet wide, and four or five long, with grates of these dimensions, and a door at one end for admitting the fuel, and the bars to be heated; the grates have on them a layer of three or four inches, in thickness, of ignited anthracite, upon which the bars are laid; but as flame from this fuel will not fill the space between the iron and the arch, and the heat is unequally distributed, the draft through the grate being more obstructed in one part than in another, the bars are frequently overheated, burnt, or melted, in spots. To remedy this defect, the improved furnace is lengthened about one foot, and furnished with a door at each end; the anthracite is laid on the grate as usual, and when the bars are heated to such a degree as not to endanger their burning, the hinder door is opened, and a small portion of bituminous coal thrown into the back part of the furnace, which, flashing into flame, fills the furnace therewith as it passes over the iron in its way to the chimney, and equalizes the heat of the bars. The improvements claimed are, "First. Making the furnace with a door at the back end, so as to admit of the bituminous coal being put into the back part of the furnace. Secondly. Using the bituminous coal on a part of the grate at the back part of the furnace, reserved for that purpose, which gives the coal an opportunity of ignition, as well as could be by a reverberatory or puddling furnace, before it comes in contact with the iron. Thirdly. In combining the use of anthracite and bituminous coal, for the purpose of heating bar, or other iron, at the same time igniting each in separate parts of the furnace." VOL. XV. No. 5.-MAY, 1835. 41 From the nature of the thing, as set forth, and the known talents and experience of the patentee, we have no doubt whatever that the foregoing is a real and great improvement in the process to which it appertains.
About this record
- Patentee
- Jim Shaw's X-patent list
- Date
- the Name and Date index of patents, USPTO records, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The residence comes from the Franklin Institute's journal.
- Burke's 1847 Patent Office list gives the same patent.