Drawings and documents
Published accounts: specification
Specification printed in the Mirror of the Patent Office (1828) with its plate
American Journal of Improvements in the Useful Arts, and Mirror of the Patent Office, vol. 1 (1828), printed p. 296 · View the page
Show the transcription Hide (768 words)
Text of the specification as printed in the Mirror of the Patent Office, machine-transcribed from the page scans (GLM-OCR); not proofread. Check the scan for figures and reference letters.
IMPROVEMENT IN THE FAMILY SPINNER.
By William W. Jones, of Thornville, Perry county, Ohio.
See plate XXVI. fig. 1.
The improved Family Spinner, is a horizontal machine, which is put in motion by pulling a band or cord; the carriage or brake of the machine sliding on two wires, drawn tight from one end to the other.
The machine is constructed of well seasoned plank or boards, four inches wide, and one and a half inch thick; thus:—Take two pieces A B, four and a half feet long; set them upright, eighteen inches apart, which will be sufficient to admit six spindles between the two head pieces A B, the spindles being three inches apart; the third piece C, two and a half feet long, placed two and a half inches from the left hand post B, then a cap piece D, twenty-five inches long, extending across the tops of ABC, dovetailed in, to hold them together; a piece F, two inches wide, tenoned into A B, eight inches from the bottom, still holding them eighteen inches apart; a piece E, at the bottom of C, tenoned into B, the spindles being placed on the brace and rest, as usual in spinning jennies, in wool factories, the bottoms of the spindles being twenty inches below D. Then two side rails G H, tenoned into the edges of A B, extending eight feet horizontally, or more, at pleasure, into the two foot pieces I I, which are each four inches wide and three and a half feet long, standing upright, and placed with their edges toward each other, and fifteen and a half inches apart G H, being tenoned into A B I I, twenty-seven inches high, the mortises in II, being large enough to admit G H, with wedges to tighten them. A piece K, on the top of II, and also L, to tie III, eight inches from the bottom, and a piece M, on the outside of I, to receive the pulley block.
Make a wheel N, one inch thick, and eighteen or twenty inches diameter, with a small wheel or whirl O, four or five inches diameter, connected to the side of N, and on the same pinion, which wheels are to run between B C.
A cylinder four inches diameter P, placed on G H, with a whirl of three inches I, on the end of P. A band is to pass round N and T, and also a band or bands round the cylinder P, and the several spindles, and a cord or band round O and S, the pulley wheel, after the manner of the pleasant spinner.
Two wires run from A and B to II, on which runs the carriage or brake for the rolls. This brake consists of four pieces each, one inch square and twenty-one inches long, forming a square, except that the hindmost piece is placed three inches from the end of the side pieces. On the front of the brake is a top piece, or clamp, to hold the rolls, after the manner of Brower's vertical spinner, fastened by a small catch with a hinge. The brake may be covered with cloth, pasteboard, or wires.
In spinning, pull the cord from O to S, with the right hand, and slide the brake with the left, while walking towards II. When the brake has arrived at II, continue to pull the cord until the yarn is sufficiently twisted, then passing to AB, with your left hand bare down the wire, and with your right continue to pull the cord which will wind the yarn on the spindles.
The guide wire is similar to that on Brower's vertical spinner, and placed between A & B. The brake is hung by four wire hooks on its ways of wire. The pulley wheel S is placed in the pulley block Q, which has several holes in it, by which it may be fastened, so as to tighten the cord from O to S. The cylinder P is fastened to two sliding pieces or rests of wood, which may be fastened on G H, by screws or keys so as to tighten the bands. The wires are tightened by moving back the foot posts II.
The number of spindles may be increased or diminished by making a correspondent alteration in the dimensions.
WM. W. JONES
Date of the patent, 27th July, 1827.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, vol. 5 (1828), p. 139 · View the page
In the machine for spinning wool and cotton, called the family spinner; William W. Jones, Thornville, Perry County, Ohio, July 27.
About this record
- Patentee
- the Journal of the Franklin Institute, Journal
- Date
- the Name and Date index of patents, Jim Shaw's X-patent list
- Invention
- the Name and Date index of patents
- Listed in
- the Name and Date index of patents, Jim Shaw's X-patent list, the Journal of the Franklin Institute, the Mirror of the Patent Office (1828), S. A. Elliot's printed list of patents, Burke's List of Patents (1847)
- A drawing was printed in the Mirror of the Patent Office (1828).
- The patentee's full name comes from the Franklin Institute's journal.
- The residence comes from the Franklin Institute's journal.
- The specification was printed in the Mirror of the Patent Office (1828).
- The Mirror of the Patent Office's supplementary list gives the same patent.
- S. A. Elliot's printed list of patents gives the same name and date.
- Burke's 1847 Patent Office list gives the same patent.