Drawings and documents
Published accounts: specification
Specification printed in the Journal of the Franklin Institute
Journal of the Franklin Institute, new ser., vol. 5 (1830), p. 308 · View the page
Text of the specification as printed in the Journal, from OCR; not proofread.
Specification of a patent for a machine for Grinding Flax Seed, and other kinds of grain, paints, medicines, and other substances. Granted to ASAHEL CROSS, and EZRA BROWN, Cazenovia, Madison County, New York, February 4th, 1830. On a horizontal shaft two feet six inches, or three feet in length and ten inches from one end of the same, is placed a cast iron wheel, eighteen inches in diameter, and one inch, or more, in thickness; the flat sides of which are turned straight and smooth. Two cast iron wheels, or cylinders, nine inches in diameter and four inches in thickness, the circular surfaces of which are turned straight and smooth, are placed on two shafts, two feet in length and near one end of the same. These shafts are placed in a horizontal position across, and at right angles with, the first mentioned shaft, and from three to four inches below the same (measuring from centre to centre) one on each side of the flat wheel, and in such a manner as to bring the smooth surfaces of the cylinders in contact with the smooth sides of the flat wheel; the outer ends of the cylinders extending as far as the outer extremity of the flat wheel at the point where they come in contact. The pivots on the ends of all the shafts run in boxes of metal, or other substance, attached to a frame prepared for the purpose. The perpendicular flat wheel constitutes the principle of the improvement in the above machine, by operating between two cylinders, or rollers, similar to those heretofore in use. Operation. This machine is propelled by water, hand, or other power, by attaching a pulley and strap, or other gear, to each shaft. The seed &c. is fed from above into the machine, on each side of the flat wheel, between that and the cylinders. The flat wheel and cylinders are put in motion in a direction calculated to draw the feed between them; the flat wheel and cylinders making an equal number of revolutions in the same time. For some uses, this machine may be made much smaller than above described; but the flat wheel and cylinders should be nearly in the same proportion to each other. The principle of this machine in its operation, in its improved form, is, it breaks the seed or substance, and at the same time, by the raking motion of the flat wheel against the cylinders, in consequence of their being placed below its centre, it effectually grinds or pulverizes it. ASAHEL CROSS, EZRA BROWN. 庸 309
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 5 (1830), p. 292 · View the page
8. For an improved Machine for Grinding Flax-seed, and other kinds of Grain, paints, medicines, and other substances; Asahel Cross and Ezra Brown, Cazenovia, Madison county, New York, February 4.
Remarks. (See the specification.)
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 5 (1830), p. 307 · View the page
The feather spring is a thin piece of steel pinned to the back of the tumbler pin, or trigger; the upper end of which, pressing against the CROSS and BROWN's machine for Grinding. hinder end of the lever, causes the notches of the tumbler to fall into a corresponding notch of the dog. The inventor claims, as his exclusive improvement, the form and arrangement of the parts of the lock, so as to render it more simple, safe, certain and effective. SAMUEL FORKER. Specification of a patent for a machine for Grinding Flax Seed, and other kinds of grain, paints, medicines, and other substances. Granted to ASAHEL CROSS, and EZRA BROWN, Cazenovia, Madison County, New York, February 4th, 1830.
Remarks. On a horizontal shaft two feet six inches, or three feet in length and ten inches from one end of the same, is placed a cast iron wheel, eighteen inches in diameter, and one inch, or more, in thickness; the flat sides of which are turned straight and smooth. Two cast iron wheels, or cylinders, nine inches in diameter and four inches in thickness, the circular surfaces of which are turned straight and smooth, are placed on two shafts, two feet in length and near one end of the same. These shafts are placed in a horizontal position across, and at right angles with, the first mentioned shaft, and from three to four inches below the same (measuring from centre to centre) one on each side of the flat wheel, and in such a manner as to bring the smooth surfaces of the cylinders in contact with the smooth sides of the flat wheel; the outer ends of the cylinders extending as far as the outer extremity of the flat wheel at the point where they come in contact. The pivots on the ends of all the shafts run in boxes of metal, or other substance, attached to a frame prepared for the purpose. The perpendicular flat wheel constitutes the principle of the improvement in the above machine, by operating between two cylinders, or rollers, similar to those heretofore in use. Operation.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.