Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (591 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 2.
United States Patent
Patent No.: X6610
Isaac Van Doren
Letters Patent
The Schedule referred to in the Letters Patent and making part of the same, containing a description in the words of the said Isaac Van Doren himself of his improvement in the Portable horse power engine to propel all kinds of machinery by the application of the endless screw.
This engine consists of a wooden frame 44 inches long, 36 inches wide, and 32 in height, see Plate I Figure 1.
Figure 2 represents a small spur wheel, of cast iron, fastened on a wrought iron axis, and in contact with the large spur wheel, see Fig 3. C represents two cross pieces notched into the Posts on the inside, and support the wrought iron axis A. Fig 3 is a cast iron spur wheel 36 inches in diameter, the plane of which is perpendicular to the horizon and is made fast on the axis A near the end. Fig 4 is a small spur wheel of cast iron firmly fixed on the axis A, and in contact with the threads of the screw, figure 5. Figure 5 represents an endless screw made of a cast iron cylinder 4 inches in length and 18 in diameter, the threads of which are on the circumference of the cylinder, projecting half an inch and inclined to its base in an angle of about ten degrees and are 3/4 of an inch asunder, and about the same in breadth. The screw is firmly fixed and supported on an upright, cast iron shaft, or axis (see the figure), the lower end of which rests in a step on the cross piece C sustained by two of the ground pillars at each end, in the middle of the frame. The upper end of the shaft passes through piece T directly over the frame, to the height of six or eight inches above the frame. On the upper end of this shaft, a lever... six feet long is fixed, (see L) to which the power is applied to put the engine in motion; and one horse, and one horse, at the end of this lever, will perform with ease, the work which requires the power of nearly five to execute in the usual way, and if four levers each to describe a circle of six feet radius, be placed at right angles on the end of the shaft above the frame, with a horse at each extreme, therefore will be nearly equal to twenty horses on the common plan of gearing.
The endless screw, although an old instrument, yet the application of,
Page 3.
United States Patent
Patent No.: X6610
I claim particularly as my own discovery, and contemplate its application as an effective agent in the construction of saw mills, grist mills, slitting mills, cotton and linen manufacturers and all steam engines and machines propelled by horse power.
Fig. 6 represents a drum or wheel fastened on the end of the straight iron shaft or axis Fig. 2, to which a strip or band may be applied to communicate motion to the various kinds of machinery. In some cases it may be expedient to substitute spinn wheels for wheels and bands to convey the power of the engine to other machines.
Plan 8 represents the horse power engine communicating motion to the new improved washing machine by the introduction of bands etc.
Signature
Witnesses
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 8 (1831), p. 341 · View the page
48. For a Horse Power Engine, to be used for propelling machinery of all kinds; Isaac Van Doren, Hopewell, Huntingdon county, New Jersey, June 13.
Remarks. This horse power engine is not a horse power steam engine, but is one intended to evade the laws of nature by causing the power of one horse to produce an effect equal to that of five. It is consequently to be "a cheap and efficacious substitute for steam and water power." A horse is to turn a shaft by means of a lever, this lever carries an endless screw which acts upon a toothed wheel. Upon the shaft of this wheel, is a large spur wheel, which takes into a pinion, giving motion to a drum, a strap from which is to drive the machinery. The inventor has, probably, not seen the necessary result of his invention, or he would have carried it still further. If the drum at the end of the train moves with the power of five horses, let him employ this to drive another horse power machine, and the next drum will have the power of twenty-five horses; and so on ad infinitum.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 8 (1831), p. 343 · View the page
53. For a Thrashing Machine; Isaac Van Doren, Hopeweli, Huntingdon county, New Jersey, June 13.
About this record
- Patentee
- DATAMP
- Date
- DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The sources give different dates; the date shown is the one most of them agree on.
- The Franklin Institute's journal confirms the date shown.
- Burke's 1847 Patent Office list gives the same patent.