Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (712 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 2.
United States Patent
Patent No.: X9442
Jeremiah Walker Phillips, Maine
Letters Patent
The Schedule referred to in these Letters Patent and making part of the same containing a description in the words of the said Jeremiah Walker Phillips himself of his improvement in the lever power machine for sawing and other purposes.
To all to whom these presents shall come. We do mean that of Jeremiah Walker Phillips in the county of Somerset and State of Maine have invented a new and useful machine called a lever power machine for sawing and other purposes and that the following is a full and exact description thereof — In the first place there is a frame about five feet long, two and a half feet wide and two feet high, which is constructed of as many pieces of timber and of such dimensions as will render it firm and strong; near one end of this frame there is a circular saw which is hung upon an iron shaft which rests upon the top of the frame and goes quite across it; the saw is placed toward one end of the shaft, just within the frame and toward the other end of the said shaft there is a pulley. The shaft is kept in its place by iron plates placed on it and screwed down to the frame. Near the other end of the frame there is another iron shaft running horizontally across the frame like the former, which is kept in its place by iron plates screwed to the frame in the same manner as the one first mentioned. Toward one end of this shaft and directly opposite to the pulley on the saw shaft, there is a large drum wheel and a flat leather band going around them and the pulley connects them together. This shaft containing the drum wheel is called the crank shaft, because it is so bent as to make three cranks, two within the frame and a little to the left of the drum and the other at the end outside the frame. The operation is performed by means of two levers as follows viz: one of the levers is long, the other short with a weight attached to its outer end which extends but
Page 3.
United States Patent
Patent No.: X9442
a little way from the frame both of these levers at their inner ends are attached to one of the bottom pieces of the frame below the saw shaft by means of joints formed of loops and staples. there is also an iron staple in each of these levers directly under the crank shaft then two iron rods looped around the two middle cranks at their upper ends and passing down in a perpendicular direction a little below the cranks and looped into the staples in the levers serve to connect the cranks and the levers together. this being done the drum wheel is started in the direction which it should go by hand. then the levers commence their up and down motion. when the outer end of the long lever which is operated by hand is raised up the short lever containing a weight on its outer end comes down and each lever carries its own crank along with it. thus by the simple operation of the long lever the whole machine is put in motion and by means of the drum and pulleys the circular saw is carried around with great rapidity and steadily and answers a valuable purpose in sawing many kinds of wood and timber. To the third crank which is situated outside of the frame by the help of suitable gear work there is attached a cross cut saw as also sundry implements for boring holes. When two persons undertake to operate the machine two long levers are to be used & the weight above mentioned is to be dispensed with. — Dated at Phillips, aforesaid the 3rd day of November Anno Domini 1836.
Witnesses:
John Balyton
Mark S. Bartlett
Lemuel H. Walker
E.L.
chfw.
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 18 (1836), p. 254 · View the page
85. For Sawing by Lever Power; Jeremiah Walker, Philips, Somerset county, Maine, February 25.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.