Drawings and documents
National Archives restored drawings: drawing
Lyman Gleason's Patent Drawing for a Carriage Spring
National Archives, Restored Patent Drawings (Record Group 241) · Full-size scan at the National Archives · Catalog record
Show the text on the drawing Hide (62 words)
Words on the drawing as machine-read by the National Archives; not checked. Useful mainly for searching.
p/152 / Shring / 21. CARRIAGES & WAGONS. / [31] Springs. / CLASSIFICATION / 8560-X / DIVISION. / mix / LYMAN GLEASON / CARRIAGE SPRING / Patented 24 1834 / Reference / A the Spring / the pin / c the lever. / Patient Office 25 Gt1838 / Made under the direction of the Commissions / of Patints in conformity with act 3 March 1877 / Hengh Sumoth / Commisioner of Patents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (436 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 1.
8560X
L. GLEASON.
Carriage-Spring.
Patented Dec. 24, 1834

A.M. PHOTO-LITHO. CO. N.Y. (OSBORNE'S PROCESS.)
Page 2.
Dec. 24, 1874
Lyman Gleason
Letters Patent
The schedule referred to in these Letters Patent and making part of the same, containing a description in the words of the said Lyman Gleason himself, of his improvement in the making or manufacturing of steel springs for the use of carriages of all kinds and wagons —
Specification or description for the cylinder lever power spring, for the use of two & four wheeled carriages & coaches of all descriptions. First, the spring is to be made of steel spring temper, from one to eight inches wide & thickness in proportion, to be welded or fastened to a pin, of cast or wrought iron, or any other metal sufficient to hold the lever. The steel is to be rolled round the pin above mentioned, from one or more times, not so close as to have it touch or hit so hard as to prevent the spring, of the wheel. The out end of the steel to be fastened to any part of the carriage gearing that may be most convenient when applied. The other end is to be fastened to the pin where the lever is to be attached. Second, the lever is to be placed at each end of the pin, and the steel spring between; or the lever in the centre, and the spring on the outside. For heavy carriages, the pin is to pass through the lever far enough to receive a rest or bearer; in such case, the out ends of the pins to be round. The lever is to be made of steel, cast or wrought iron, or any metal of sufficient strength for the lever. The lever to be seven inches or more in length. Third, for a single spring, it is to open at one end, as wide as the steel and fastened on each end of the pin. For a double spring, it may be fastened in the centre without splitting. The length of the lever must be regulated by the size of the carriage, or the place to which the out end is fastened. For further explanation reference is had to the draft hereto annexed, which forms part of this schedule.
Witnesses
James T. Merritt
George W. Bay
416 W. 8th
Lyman Gleason
(Patented 24 Dec. 1874)
582
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 15 (1835), p. 144 · View the page
627. Steel carriage springs. Lyman Gleason, Stafford, N. Y.
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 16 (1835), p. 35 · View the page
57. For Steel Carriage Springs; Lyman Gleason, Stafford, Genessee county, December 24.
Remarks. A steel bar is to be bent spirally, like the spring of a house be". The outer end of this spring is to form a strap, by which it is to be attached to the carriage, and its inner end to a pin, by which it is to be connected to the body. There is no claim made, nor are there any letters of reference to the drawing.
About this record
- Patentee
- DATAMP
- Date
- DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- The sources give different dates; the date shown is the one most of them agree on.
- The Franklin Institute's journal confirms the date shown.
- Burke's 1847 Patent Office list gives the same patent.