Drawings and documents
USPTO scan
The patent as scanned by the USPTO
U.S. Patent and Trademark Office · Google Patents
Show the transcription Hide (671 words)
Machine transcription (LightOnOCR) of the pages as scanned by the USPTO, most of them the handwritten copies made when the records were restored after the 1836 fire. Not checked; it can misread handwriting, so compare it with the scan.
Page 2.
United States Patent
Patent No.: X8801
Lewis Aspinwall
Letters Patent
The schedule referred to in these Letters Patent and making part of this patent containing a description in the words of the said Lewis Aspinwall himself of his improvement in making friction bushes or bores for the shoes for blocks and for other purposes.
To all persons to whom these presents shall come. Be it known that I, Lewis Aspinwall of Albany in the County of Albany and State of New York, have invented a new and useful improvement in the art or mode of casting friction bushes for block shoes and for any other purpose for which such bushes may be wanted. These bushes have been heretofore cast in sand or other earth and afterwards finished by turning, drilling, etc., which mode as the metal of which they are made is necessarily hard is comparatively slow and tedious. Now the improvement of which I here claim to be the inventor is the casting all parts of said friction bushes (except the pins or studs) which may be made of wire, in smooth metallic moulds in such manner as to need no finishing by turning or any other operation after having the moulds emptied or channelling or taking the sharp corners from the cylinders which also may be effected in the moulds, but which I think best to do afterwards and also except taking off the spires or gates from the several articles. To render this more fully, it may be proper to state that the common patent friction bush now in use consists of a cylindrical box commonly made in two halves, put together laterally, each of which halves is open at the end making when put together a cylinder, open at each end, with an inward flange at each end to contain and steady the rollers and this hollow cylinder contains six more or less friction rollers which roll round within the said box leaving the intermediate space in the center for the pins, shaft or quiggeon, on which they are to turn, or which is to turn in them. The whole of the article then consists of two similar half boxes and of the rollers each of which roller is simply a plain cylinder with a small hole at each end for the steady pins, together with two flat circular rims containing the
Page 3.
United States Patent
Patent No.: X8801
the steady fins, which two ends are also held together by any convenient number of studs of wire, the ends of which are riveted on the outsides of the said circular plates or rims. But the cylindrical box which contains the rollers may be cast whole instead of being in halves and the forms and proportions of the whole may be varied to suit the use for which it is intended. I save the labor and consequent cost of turning and otherwise finishing. I cast the said boxes, rollers, and circular rims with the steady fins in smooth metallic moulds neatly fitted together to suit the form of each article, so that they leave the mould in a state of complete finish ready to be put together with the exceptions above named. My moulds I make of cast wrought iron, but they may be made of any other suitable metal; but of whatever metal made, I claim the casting said articles in smooth metallic moulds so as to need no subsequent finish except as already specified, as my invention and constituting the improvement herein specified. The exterior form of the moulds and the means of putting them together may be as infinitely varied and is so much dependent on the fancy of the constructor as to need no specific description.
Witnesses
S. A. Cole
Samt, Glyadenburgh
Lewis Aspinwall
(658 words)
Published accounts: journal notice
Notice in the monthly list of patents
Journal of the Franklin Institute, new ser., vol. 15 (1835), p. 435 · View the page
240. Friction bushes.-L. Aspinwall, Albany, New York,
Published accounts: journal notice
Notice in the monthly list of patents, with remarks
Journal of the Franklin Institute, new ser., vol. 16 (1835), p. 329 · View the page
42 70. For Friction Boxes for the sheaves of blocks, &c.; Lewis Aspinwall, city of Albany, New York, April 22.
Remarks. The claim under this patent is to "the casting said articles in smooth metallic moulds, so as to need no subsequent finish, as my invention, and constituting the improvements herein specified;" said articles being the rollers and frame works for the friction bushes sometimes used in blocks. The process of casting in metallic moulds to furnish articles in cast-iron at once extremely hard, and true, is one well understood, and it may very fairly be doubted whether a patent can be sustained for casting a particular kind, or size, of rollers, &c. in a way perfectly well known, and therefore not properly coming under the denomination of an invention, or discovery.
About this record
- Patentee
- DATAMP
- Date
- the Name and Date index of patents, DATAMP, USPTO records
- Invention
- DATAMP
- Listed in
- the Name and Date index of patents, DATAMP, USPTO records, Jim Shaw's X-patent list, the Journal of the Franklin Institute, Burke's List of Patents (1847)
- Burke's 1847 Patent Office list gives the same patent.